Download Print this page

moyno 300 Series Service Manual

Motorized pumps with magnetic drives

Advertisement

Quick Links

DESIGN FEATURES
Housing:
PVC or Non-Metallic
Pump Rotor: Titanium
Pump Stator: FPM, NBR (Nitrile), EPDM
Seal:
Sealless design
Motor Shaft: Hardened Carbon Steel
Motor:
.5 and 1 HP, 60 Hz, 1750 RPM, totally
enclosed fan cooled (TEFC), C-Faced,
3 Ph, 230/460V (other motor
options available; consult sales
representative)
INSTALLATION
Mounting Position.
Pump may be mounted in any
position.
Pre-Wetting.
Prior to connecting pump, wet pump
elements by adding fluid to be pumped into suction and
discharge ports.
Turn pump over several times in a
clockwise direction to work fluid into pump elements.
Piping. Piping to pump should be self-supporting to avoid
excessive strain on pump housings.
suction and discharge port sizes of each pump model. Use
pipe "dope" or tape to facilitate disassembly and to provide
seal on pipe connections.
Electrical.
Follow the wiring diagram on the motor
nameplate or inside the terminal box for the proper
connections. The wiring should be direct and conform to
local electrical codes. Check power connections for proper
voltage.
Voltage variations must not exceed ±10% of
nameplate voltage.
Motor is provided with internal
automatic overload protection.
To prevent damage to pump, pump rotation must be
clockwise when facing pump from motor end.
OPERATION
DO NOT RUN DRY. Unit depends on liquid pumped for
lubrication. For proper lubrication, flow rate should be at
least 10% of rated capacity.
Pressure and Temperature Limits.
maximum discharge pressure of each model. Temperature
limit for any application cannot exceed 140°F.
SERVICE MANUAL
®
Moyno
300 Series Motorized Pumps with
Magnetic Drives
331, 332, 333, 344 MODELS
Caution: Suction pressure should never be greater than
See Table 1 for
Mag 331
Mag 332
Mag 333
Mag 344
TROUBLESHOOTING
WARNING: Before making adjustments, disconnect
Failure to Pump.
1.
See Table 1 for
Mag Drive 500
discharge pressure.
Table 1. Pump Data
Suction
Discharge
Pump
Port
Port
Model
(NPT)
(NPT)
1"
3/8"
1"
3/8"
1"
3/8"
1"
3/8"
power
source
pressure from system prior to disassembly.
Failure to do so could lead to electric shock
or serious bodily harm.
Motor will not start: Check power supply. Voltage must
be ± 10% of nameplate rating when motor is in locked
rotor condition.
Section:
Mag Drive 500 Pumps
Page: 1 of 4
Date: January 2010
Voltage
Discharge
Rating
Pressure
(VAC)
(psig)
See Motor Nameplate
100
For Voltage Ratings
See Motor Nameplate
80
For Voltage Ratings
See Motor Nameplate
50
For Voltage Ratings
See Motor Nameplate
40
For Voltage Ratings
and
thoroughly
bleed

Advertisement

loading
Need help?

Need help?

Do you have a question about the 300 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for moyno 300 Series

  • Page 1 Mag Drive 500 Pumps Page: 1 of 4 Date: January 2010 SERVICE MANUAL ® Moyno Mag Drive 500 300 Series Motorized Pumps with Magnetic Drives 331, 332, 333, 344 MODELS DESIGN FEATURES Housing: PVC or Non-Metallic Pump Rotor: Titanium Pump Stator: FPM, NBR (Nitrile), EPDM...
  • Page 2 Stator torn; possible excessive pressure: Replace 10. Remove the thrust washer (11) from the rotor shaft (10). stator; check pressure at discharge port. 11. Remove the rotor (22), inner magnet (9), shaft bushing Wrong rotation: Rotation must be clockwise when (13), and rotor end bushing (12) as an assembly.
  • Page 3 18. Using eight socket button head cap screws (18), 21. Place the pump assembly onto the motor (1) and outer secure the stator housing (17) to the discharge housing magnet assembly (4), being careful not to put any (14). fingers or hands between the two magnets. Secure the pump assembly to the motor using four socket 19.
  • Page 4 Stator Ring (331 and 332 Only) 3207812000 Not Applicable © 2010 by Moyno, Inc. ® Moyno is a registered trademark of Moyno, Inc. Printed in U.S.A. Moyno, Inc. is a part of the Fluid Management Group of Robbins & Myers, Inc.

This manual is also suitable for:

Mag drive 500Mag 331Mag 332Mag 344Mag 333