Page 1
® WORLDWIDE EQUIPMENT O P E R A T I O N M A N U A L Hand-held Applicator 97111 97112 97116 GLOBAL AVAILABILITY GLOBAL SERVICE...
Page 2
• Worldwide Availability • Worldwide Service • Application support for integrating both the adhesive and equipment interface For additional information on Loctite Worldwide Adhesives and Equipment, please contact your local Loctite representative for a copy of the Loctite Design Handbook.
Contents Page No. Please observe the following Emphasized Sections Items Supplied For Your Safety Usage Description Operating Elements and Connections 2, 3 Theory of Operations Technical Data Installation Connecting the Unit 5, 6 Mounting the Hand Grip Dispensing First Operation 5.1.1 Priming the Hand-held Applicator 5.1.2...
The applicators can be used in a hand-held fashion or mounted in a stationary manner that allows easy production line integration for fulfilling your dispensing needs. Loctite provides a selection of product reservoirs that could be used with the various Hand-held applicators that are available.
The reservoir is then pressurized from a Loctite Controller using clean, filtered dry air. Air within the reservoir will push down on the liquid in the bottle and force it through the product feedline to the dispense shutoff valve.
Installation Connecting the Unit Connecting to the Product Reservoir A) .5 Liter #97105/#97106 2 Liter #97107/#97108 max. 97111 2 m/ 6.6 ft. max. 2 m/ 6.6 ft. 97112/97116 B) 300 ml Cartridge Reservoir max. 97111 #97109/#97110 2 m/ 6.6 ft.
Page 11
Installation Connecting to the Semi-Automatic Controller (97112 or 97116 only) C) Semi- Automatic Controller #97102 97116 97102 max. 2 m/ 6.6 ft. 1: S ta rt 2: R es er vo ir Lo ct 97112/97116 (Ir el in Ge 90 –2 ca t.n rm an an d...
97111 Perform the filling of the product line according to the operating ® instructions of the LOCTITE Manual Controller 97101. 97112 / 97116 Perform the filling of the product line according to the operating instructions of the LOCTITE Controller 97102.
LOCTITE Manual Controller 97101. 97112 / 97116 Initiate a time controlled dispensing start (approx. 0.50 sec. long - see the operating instructions of the LOCTITE ® Controller 97102. When necessary, change the piston stroke with the adjustment knob 8: Product drips: –...
Dispensing 5.1.2.2 Mounting the Feedtube Adapter For viscous products, a feedtube adapter with a 9.5 mm product feedline is available by ordering Part Number 97220. When mounting the feedtube adapter, the product feedline must be cut off. The contact of anaerobic products with the metal of a knife or other objects can cause curing and lead to malfunction of the dispensing.
Dispensing Shutdown To protect anaerobic products from curing, remove needle leaving Luer-Lok Adapter exposed to air. To protect all other product from curing, place a protective cap on the dispensing needle. If for some reason the product being dispensed changes, contact your local salesperson for the recommended procedures.
(Section 5.1.1). – Controller incorrectly adjusted. Check the controller. Loctite Service. – Product reservoir not switched on or Check to make sure product reservoir is reservoir pressure too low. pressurized and/or increase reservoir pressure.
Accessories and Spare Parts Fold out the illustration inside the front cover. No. Description Loctite Order No. Hand-held Applicator Pistol Grip ..............97237 Dispense Needle, Polyethylene – Conical (PPC), Dispense Needle PPC16GA (50 pcs/box), ID Size 1.20 mm, grey ....97221 31.8 mm Dispense Needle PPC18GA (50 pcs/box), ID Size 0.84 mm, green ....97222...
A claim of defect in materials or workmanship in any Products shall be allowed only when it is submitted to Loctite in writing within one month after discovery of the defect or after the time the defect should reasonably have been discovered and in any event, within twelve months after the delivery of the Products to the purchaser.
Page 19
31.8 mm 30.0 mm 12.7 mm 56.1 mm 38.6 mm...
Page 20
DIN EN 292 Part 1 11.1991; DIN EN 292 Part 2 11.1991 Date / Manufacturer’s signature 1995 Information regarding the Signer President – Worldwide Manufacturing (Peter G. Dowling) For changes to the unit that were not approved by Loctite, this declaration loses its validity.