Subscribe to Our Youtube Channel
Related Manuals for Leica mojo3D
Summary of Contents for Leica mojo3D
- Page 1 Leica mojo3D: Direct Section Control Amazone Amatron+ Installation Guide Version 1.2 English...
-
Page 2: Table Of Contents
Leica mojo3D Direct Section Control – Amazone Amatron+ Table of Contents Introduction ........................... 3 Amatron+ Verification ........................4 Installation ............................. 5 System Configuration ........................6 Controller Configuration ......................... 8 Spraying With The Amatron+ ......................9 General Troubleshooting ....................... 11 Appendix A – Changing Section Channels ..................13... -
Page 3: Introduction
This manual contains instructions for installing and setting up the product to operate with a Leica mojo3D. Read carefully through this manual before starting the installation. When this product is used with the Leica mojo3D it is mandatory to observe the safety directions and instructions contained in the corresponding user manual. -
Page 4: Amatron+ Verification
Firmware version For the mojo3D to be able to successfully control the Amazone sprayer, the sprayer must be running firmware version 7.0 7.0..7 7 7 7 or higher. Follow these steps to verify the Amazone firmware version: 1. -
Page 5: Installation
Installation Connect data cable 1. Install the Leica mojo3D Port Expansion Cable by connecting it to the mojo3D. 2. Connect the data cable to CAN 2 (the grey three pin connector) on the mojo3D Port Expansion Cable. 3. Connect the data cable to the centre DB9 connector on the bottom of the Amatron+ controller in-line with the cables and accessories supplied by Amazone. -
Page 6: System Configuration
4. Tap Amazone Amatron+, to select it as the section controller. 5. Tap Sprayer Mode, to select it as the implement mode; then tap to continue. 6. Tap mojo3D and Touch to configure the mojo3D turn on/off by touching the screen. 7. Tap to continue to the Section Control Setup... - Page 7 Channels to enter a different configuration depending on the number of sections Channels Channels being used..Refer to the Leica mojo3D user manual for instructions on configuring calculating and updating the latency values. Leica mojo3D Direct Section Control –Amazone Amatron+...
-
Page 8: Controller Configuration
Return to the main screen by pressing the ESC ESC key. 8. Review the Section Control Setup Section Control Setup Section Control Setup Section Control Setup on the mojo3D to ensure the number of sections, section widths and total implement width are correct. -
Page 9: Spraying With The Amatron
Spraying With The Amatron+ Start Treating 1. Turn on the mojo3D and the Amatron+, use the button to get the Amatron+ to the main screen 2. Unfold the sprayer booms and ensure the boom is unlocked. The lock icon is shown on the main screen of the Amatron+. - Page 10 Leica mojo3D Direct Section Control – Amazone Amatron+ 3. Once the mojo3D has a guidable position the system is ready to spray. Enable auto-section control on the mojo3D with the spray button on the bottom left of the main screen. Enable spray using the...
-
Page 11: General Troubleshooting
Solution Solution Solution Solution The sprayer does not spray when treatment is Both the Amatron+ and mojo3D must be Troubleshooting enabled on the mojo3D. enabled for auto section spraying to occur. Press the spray button on the main screen of the mojo3D and the Amatron+ to enable spray. - Page 12 Leica mojo3D Direct Section Control – Amazone Amatron+ Check the number of sections set on the mojo3D (in the Section Control Setup Section Control Setup Section Control Setup Section Control Setup screen) matches the number of sections set on the Amatron+.
-
Page 13: Appendix A - Changing Section Channels
2. On the main navigation screen, tap the settings button. 3. On the flyout menu, tap the Implement Setup button. 4. Tap until the Section Control Setup Section Control Setup Section Control Setup screen is displayed. Section Control Setup Leica mojo3D Direct Section Control –Amazone Amatron+... - Page 14 Leica mojo3D Direct Section Control – Amazone Amatron+ 5. Using the table below determine which Section Channel number to Enter for each section depending on the number of sections used. Channel Number Of Sections...
- Page 15 6. Enter the Section Channel number by tapping the corresponding section at the top of the screen and changing the Section Channel to the appropriate number. 7. Continue this for all sections. 8. Tap to save the changes. Leica mojo3D Direct Section Control –Amazone Amatron+...
- Page 16 Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland Phone: +41 71 727 31 31 www.leica-geosystems.com...
Need help?
Do you have a question about the mojo3D and is the answer not in the manual?
Questions and answers