Related Manuals for Britax STEELCRAFT PC8343 SERIES
Summary of Contents for Britax STEELCRAFT PC8343 SERIES
- Page 1 STRIDER SIGNATURE SECOND SEAT IMPORTANT: KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE www.britax.com.au Series PC8343...
-
Page 2: Important Notes
WARNINGS WARNINGS: • SECURE THE CHILD IN THE HARNESS AT ALL TIMES. • DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR USE WITH THIS STROLLER BY BRITAX. • IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH THIS STROLLER. • THE MAXIMUM WEIGHT OF THE CHILD USING THIS SECOND SEAT IS NOT TO EXCEED 17KG. IMPORTANT NOTES: • DO NOT USE THIS SECOND SEAT WITH ANY OTHER MODELS OF STROLLER. • THE SECOND SEAT MUST BE CORRECTLY FITTED AND LOCKED ONTO THE STROLLER FRAME. • THE SECOND SEAT CAN ONLY BE USED IN THE FORWARD FACING POSITION, CONNECTED TO THE REAR OF THE STROLLER. • DO NOT OVERLOAD THE STROLLER. OVERLOADING WILL CAUSE THE STROLLER TO TIP BACKWARDS. This CAUTION Symbol is shown at certain steps in this Instruction Manual to highlight the danger of being injured by moving parts. CAUTION www.britax.com.au... -
Page 3: Manual Handling Techniques
• Change direction by turning your feet and not your back. • To set the load down, squat down, keep your head up and • Let your legs do the work. Remember to ‘THINK TALL ’ chest lifted, shoulders relaxed, chin tucked in and head level. www.britax.com.au... -
Page 4: Parts List
PARTS LIST 1x second seat 1x Head pillow + 2x Shoulder Harness Pads 1x Set of extension Adaptors www.britax.com.au... - Page 5 SECOND SEAT FEATURES Canopy Pick-a-boo window second seat release button Support bar second seat mounting pin www.britax.com.au...
-
Page 6: Important Note
To expose mesh window, open the To expose mesh panel lift the window flap to the back. mesh cover. www.britax.com.au... - Page 7 Slide the shoulder harness pads To use the head pillow, place the onto the shoulder harness straps head pillow on the stroller seat and adjust to the position which fits and connect the hook and loop to comfortably on the child. desired position. www.britax.com.au...
- Page 8 STROLLER. PLEASE NOTE: Extension Receivers can be used to create more space between the stroller seat and second seat. (Refer to page 18) Engage the stroller brake. Rotate the pivotal handle to the highest position. Raise the stroller seat backrest to the fully upright position. Unhook the straps of the back of the basket and put in the basket. www.britax.com.au...
- Page 9 Line up the arrow 1) on the stroller frame then support bars on the second seat pull downwards (as indicated by with the lower mounting brackets arrow 2). on the inside of the stroller frame (located on rear wheel housing). www.britax.com.au...
- Page 10 Pull the second seat upwards to frame (located on rear wheel ensure it is locked onto the stroller housing). frame. www.britax.com.au...
- Page 11 SECOND SEAT OPERATION ADJUSTING THE BACKREST WARNINGS: • THE UPRIGHT POSITIONS ARE NOT SUITABLE FOR USE WITH CHILDREN LESS THAN 6 MONTHS OLD. • THE LOWEST RECLINE POSITION SHOULD BE USED TO TRANSPORT BABIES. THE BACKREST CAN BE ADJUSTED TO A MORE UPRIGHT POSITION AS THE CHILD GROWS OLDER AND IS ABLE TO SUPPORT ITS HEAD WITHOUT ASSISTANCE. PLEASE NOTE: If the child is sitting in the seat, support the backrest as it reclines. If you have difficulty adjusting the backrest you may need to remove the child from the seat to allow you to raise or lower the backrest with ease. Lift the recline lever at the top of the second seat and hold while raising or lowering the backrest to the desired position. www.britax.com.au...
- Page 12 While still holding the recline lever, press the second seat safety release button and continue to lower the seat. Lift the second seat up and away from the stroller frame. www.britax.com.au...
- Page 13 ‘click’. Thread the waist strap buckle Repeat the procedure on the tongues through the shoulder strap other side. tongue guides. Please ensure it’s locked. www.britax.com.au...
- Page 14 DO NOT SLIDE 3 BAR SLIDER OVER THE SEWN TAB ON SHOULDER HARNESS. OPENING THE HARNESS Release the harness by pressing the centre button in on the crotch buckle while pulling the waist tongues out of the crotch buckle. www.britax.com.au...
- Page 15 To change the shoulder harness Select the appropriate shoulder height, push the shoulder harness height and pull each harness tongue out of the Shoulder harness tongue current harness slot and through through the harness slot. the back of the seat. www.britax.com.au...
- Page 16 SECOND SEAT OPERATION FOLDING THE STROLLER WITH SECOND SEAT IMPORTANT NOTE: PLEASE REFER TO PAGE 3 FOR SMART LIFTING TECHNIQUES. • REMOVE THE CHILD FROM THE SECOND SEAT BEFORE COMMENCING A FOLDING OPERATION. • FOLD THE SECOND SEAT SLOWLY AND BE CAREFUL WHERE YOU PLACE YOUR HANDS. • WHEN FOLDING THE SECOND SEAT BE AWARE OF THE DANGER OF BEING INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE PROCESS. • KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS. • THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE INJURED THEN THE SECOND SEAT IS BEING FOLDED, DUE CARE TO BE EXERCISED. • KEEP CHILDREN CLEAR OF THE STROLLER DURING FOLDING OF THE STROLLER. • FOLD THE SECOND SEAT BEFORE FOLDING THE STROLLER. • INCORRECT FOLDING MAY CAUSE DAMAGE TO THE STROLLER AND FRAME. • PLEASE FOLLOW THE FOLDING INSTRUCTIONS CAREFULLY. www.britax.com.au...
- Page 17 Fully lift the recline lever and lower the second seat to the lowest position. While still holding the recline lever, press the second seat safety release button and continue to lower the seat. PLEASE NOTE: When you folding the stroller with the second seat, make sure the handle height is set to the highest posion aligned with frame to prevent the handle coming in contact with the second seat and causing damage to the stroller. Handle height aligned with frame www.britax.com.au...
- Page 18 REMOVING THE SECOND SEAT EXTENSION RECEIVERS To remove the receivers, press in and hold the button, then pull the adaptor up and out of the frame sockets. www.britax.com.au...
- Page 19 The stroller seat can the receivers. be adjusted with all 4 positions when facing forward. The bassinet is not recommended to use with the second seat with or without extension receivers as there is limited space for second seat occupant. www.britax.com.au...
- Page 20 MUST BE REMOVED FROM THE SECOND SEAT. Remove the second seat from the Unfasten all the hook and loop strips stroller and remove the canopy. as indicated. And then pull the cover Slide the webbing out of the D-rings. over the frame. www.britax.com.au...
- Page 21 REMOVING THE BABY CAPSULE TO THE SECOND SEAT FRAME Squeezing and holding the Lift the Baby Capsule from the handle latch and rotate the second seat frame. handle up to unlock the Baby Capsule. www.britax.com.au...
- Page 22 MUST BE REMOVED FROM THE SECOND SEAT. Pull the cover over the frame. Pull Fasten all the hook and loop strips the webbing through the button holes as indicated. Attach the canopy. and connect with D-rings. (Refer to page 6) www.britax.com.au...
-
Page 23: Care And Maintenance
- tighten if required. To maintain the safety of your nursery product, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by Steelcraft. THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. www.britax.com.au... - Page 24 CUSTOMER SERVICE 1300 303 330 - Australia 0508 688 822 - New Zealand Due to our continuing program of development, Britax reserves the right to alter the specifications, color or design without any further notice. The Steelcraft trademark is the property of Britax Childcare Pty.Ltd - Australia.
Need help?
Do you have a question about the STEELCRAFT PC8343 SERIES and is the answer not in the manual?
Questions and answers