Emotron VFX 2.0 Instruction Manual page 12

9.4 Programming during operation .............................. 47
9.5 Editing values in a menu ........................................ 47
9.6 Copy current parameter to all sets ........................ 47
9.7 Programming example............................................ 48
10. Serial communication ................................. 49
10.1 Modbus RTU ............................................................ 49
10.2 Parameter sets........................................................ 49
10.3 Motor data ............................................................... 50
10.4 Start and stop commands ...................................... 50
10.5 Reference signal ..................................................... 50
10.6 Description of the EInt formats .............................. 50
11. Functional Description................................ 55
11.1 Preferred View [100]............................................... 55
11.1.1 1st Line [110].......................................................... 55
11.1.2 2nd Line [120] ........................................................ 56
11.2 Main Setup [200] .................................................... 56
11.2.1 Operation [210]....................................................... 56
11.2.2 Remote Signal Level/Edge [21A]........................... 59
11.2.3 Mains supply voltage [21B].................................... 60
11.2.4 Motor Data [220] .................................................... 60
11.2.5 Motor Protection [230] ........................................... 64
11.2.6 Parameter Set Handling [240] ............................... 67
11.2.7 Trip Autoreset/Trip Conditions [250]..................... 69
11.2.8 Serial Communication [260] .................................. 75
11.3 Process and Application Parameters [300] .......... 78
11.3.1 Set/View Reference Value [310] ........................... 78
11.3.2 Process Settings [320] ........................................... 78
11.3.3 Start/Stop settings [330] ....................................... 82
11.3.4 Mechanical brake control....................................... 86
11.3.5 Speed [340]............................................................. 88
11.3.6 Torques [350].......................................................... 91
11.3.7 Preset References [360] ........................................ 92
11.3.8 PI Speed Control [370] ........................................... 93
11.3.9 PID Process Control [380] ...................................... 94
11.3.10 Pump/Fan Control [390] ........................................ 98
11.3.11 Crane Option [3A0] ............................................... 104
11.4 Load Monitor and Process Protection [400] ....... 106
11.4.1 Load Monitor [410] ............................................... 106
11.4.2 Process Protection [420]...................................... 110
11.5 I/Os and Virtual Connections [500]..................... 112
11.5.1 Analogue Inputs [510] .......................................... 112
11.5.2 Digital Inputs [520] ............................................... 119
11.5.3 Analogue Outputs [530] ....................................... 120
11.5.4 Digital Outputs [540] ............................................ 124
11.5.5 Relays [550] .......................................................... 125
11.5.6 Virtual Connections [560]..................................... 126
11.6 Logical Functions and Timers [600] .................... 127
11.6.1 Comparators [610] ............................................... 127
11.6.2 Logic Output Y [620] ............................................. 131
11.6.3 Logic Output Z [630] ............................................. 133
11.6.4 Timer1 [640] ......................................................... 134
11.6.5 Timer2 [650] ......................................................... 136
11.7 View Operation/Status [700] ............................... 137
11.7.1 Operation [710]..................................................... 137
4
11.7.2 Status [720] .......................................................... 139
11.7.3 Stored values [730] .............................................. 142
11.8 View Trip Log [800] ............................................... 143
11.8.1 Trip Message log [810]......................................... 143
11.8.2 Trip Messages [820] - [890] ................................ 144
11.8.3 Reset Trip Log [8A0] ............................................. 145
11.9 System Data [900]................................................ 145
11.9.1 VSD Data [920] ..................................................... 145
12. Troubleshooting, Diagnoses and Mainte-
nance 147
12.1 Trips, warnings and limits..................................... 147
12.2 Trip conditions, causes and remedial action ...... 148
12.2.1 Technically qualified personnel............................ 148
12.2.2 Opening the variable speed drive ........................ 148
12.2.3 Precautions to take with a connected motor ...... 148
12.2.4 Autoreset Trip ........................................................ 148
12.3 Maintenance ......................................................... 151
13. Options........................................................ 153
13.1 Options for the control panel................................ 153
13.2 EmoSoftCom.......................................................... 153
13.3 Brake chopper....................................................... 153
13.4 I/O Board ............................................................... 155
13.5 Output coils ........................................................... 155
13.6 Serial communication and fieldbus ..................... 155
13.7 Standby supply board option................................ 155
13.8 Safe Stop option.................................................... 155
13.9 Crane option board ............................................... 157
13.10 Encoder.................................................................. 157
13.11 PTC/PT100 ............................................................ 157
14. Technical Data ........................................... 159
14.1 Electrical specifications related to model ........... 159
14.2 General electrical specifications.......................... 163
14.3 Operation at higher temperatures ....................... 164
14.4 Dimensions and Weights...................................... 165
14.5 Environmental conditions..................................... 166
14.6 Fuses, cable cross-sections and glands.............. 167
14.6.1 According IEC ratings ............................................ 167
14.6.2 Fuses and cable dimensions according NEMA ratings
169
14.7 Control signals....................................................... 171
15. Menu List .................................................... 173
Index ........................................................... 181
Emotron AB 01-4429-01r2