Download Print this page

Arrow Storage Products AT101 Owner's Manual & Assembly Instructions

Universal attic kit

Advertisement

Quick Links

Owner's Manual & Assembly Instructions
TQ01
Universal Attic Kit
Model No. AT101
IMPORTANT: Before you start, re-
move Owner's Manual & Assembly
Instructions from main carton of your
storage building and locate Interior
Dimensions on the front cover.
Kit fi ts all 10' wide mid wall braced
ARROW storage buildings produced
since 1979. Kit can be adapted easily
for buildings with no mid wall frame,
for older buildings and buildings by
other manufacturers by drilling as
needed.
Remove the parts from the carton and
lay them out in similar groups with
the part numbers facing up. Check
the part numbers and quantity with
the parts list.
Before you start, read the entire
manual to plan how you want to use
your Attic Kit.
704970807
65103
#8-32 Hex Nut (48)
Keep this Owner's Manual for future reference.
* If you fi nd a part is missing, include the model no. of your kit and contact:
Arrow Group Industries, Inc.
Customer Service Department
Route 50 East
1-800-851-1085
Part
Part
Number
Description
8225
Post
8226
Long Attic Channel
8227
Short Attic Channel
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE
TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MIS-
HAP. WEAR GLOVES WHEN HANDLING METAL PARTS.
65923
#8-32x3/8" Bolt (48)
Breese, Illinois 62230
Quantity
in Carton
8
4
2
Check
List

Advertisement

loading

Summary of Contents for Arrow Storage Products AT101

  • Page 1 Owner's Manual & Assembly Instructions TQ01 Universal Attic Kit Model No. AT101 IMPORTANT: Before you start, re- 65923 65103 move Owner's Manual & Assembly #8-32 Hex Nut (48) #8-32x3/8” Bolt (48) Instructions from main carton of your storage building and locate Interior Keep this Owner's Manual for future reference.
  • Page 2 Step 1 TQ02 Position long attic channels as shown. Interlock channels and telescope them to proper dimension for your building. Align holes and fasten together using bolts and nuts. See Fig. 1. Make two complete as- semblies using correct interior width. LONG ATTIC CHANNEL 8226 FIGURE 1 8226...
  • Page 3 Step 2 TQ03 REAR Install two posts at the rear cor- ner of building by removing the two fasteners in the framework. Interlock the two posts and telescope them to the proper length between the upper and mid wall frames. Tabs on ends 26 3/8"...
  • Page 4 Step 3 TQ04 Position long attic channel as- semblies at the desired height to the posts and fasten using two or three bolts and nuts on both sides. Repeat procedure on next posts, making sure channels are level by using the same set of holes on each post.
  • Page 5 Step 4 TQ05 Position short attic channels between long channels as shown. Depending on width of the wall panel on your building, follow one of three procedures below, fastening chan- nels with four bolts and nuts. 2 DIAGONAL PROCEDURES STRAIGHT PROCEDURE SHORT ATTIC CHANNEL 8227...
  • Page 6 Horizontal Siding Buildings TQ06 If you are installing the Attic Kit in a Horizontal Siding building, drilling of the siding with a 1/4" diameter drill will be necessary if building is already assembled. If there are no holes in the framework, drilling will be required.
  • Page 7 IMPORTANT CAUTION NOTE The Universal Attic Storage Kit was designed to support weight equally spaced over the entire kit. The total weight of all shelving on the walls is a 250 lb. load limit. Caution should be kept in mind at all times as to the weight of the material being stored on this kit.
  • Page 8: Other Uses

    Other Uses TQ08 Kit can be attached through the sheet rock into studs or directly to studs using at least a #10 wood screw. • Garage – Add extra storage space up and out of the way with an attic kit hung from rafters or beams. •...