1. Manuals
  2. Brands
  3. Linde Manuals
  4. Measuring Instruments
  5. MT Tracker BBQ
  6. Operating manual

Linde MT Tracker BBQ Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

MT Tracker BBQ™
Operating Manual

Advertisement

Table of Contents
loading

Related Manuals for Linde MT Tracker BBQ

Summary of Contents for Linde MT Tracker BBQ

  • Page 1 MT Tracker BBQ™ Operating Manual...

  • Page 2: Table Of Contents

    MT Tracker BBQ Operating Manual Contents. Description Smart device setup Cylinder setup Using the app Battery replacement Warranty Safety guidelines Specifications Troubleshooting tips Important Notice This document has been prepared by BOC Limited ABN 95 000 029 729 (‘BOC’), the information. This document does not take into account the particular circumstances as operating instructions and has been prepared in good faith.

  • Page 3: Description

    MT Tracker BBQ Operating Manual Description MT Tracker BBQ™ sensor accurately detects LPG cylinder fill levels and sends the status ® via Bluetooth to our mobile app. You can also rename sensors, set auto alerts or add multiple sensors. Available for both iOS and Android devices.

  • Page 4: Smart Device Setup

    To add new sensors make sure the scanning icon is spinning The first time you use your MT Tracker BBQ™ press and hold SYNC button on your MT Tracker BBQ™ until it is found.
  • Page 5 MT Tracker BBQ Operating Manual The sensor will then appear on your app as a new device. Sensor is now Sync’d. You may now proceed to installing the sensor on the cylinder.

  • Page 6: Cylinder Setup

    MT Tracker BBQ Operating Manual Cylinder setup The cylinder should be kept upright at all times throughout the installation process. Clean the bottom of the cylinder of any debris, excess paint, and rust. The sensor mounts to the bottom centre of the cylinder using magnets.

  • Page 7: Using The App

    MT Tracker BBQ Operating Manual Using the app Adding more sensors will keep adding to the sensor list. Up to 50 sensors can be added. Selecting a sensor from the list takes you to the sensor’s info screen that shows the battery condition, Bluetooth signal strength, and detection quality.
  • Page 8 MT Tracker BBQ Operating Manual Selecting the pencil icon will bring up the settings page for the sensor, where you can edit the sensor name, select your cylinder size or enter an arbitrary custom size, set LPG level alarm threshold and...
  • Page 9 MT Tracker BBQ Operating Manual To remove a sensor from the app list, swipe left on the sensor in the list. A delete button will appear. Select delete to confirm removal of the sensor from the app.

  • Page 10: Battery Replacement

    MT Tracker BBQ Operating Manual Battery replacement WARNING: EXPLOSION HAZARD-BATTERIES MUST ONLY BE CHANGED IN AN AREA FREE OF IGNITABLE CONCENTRATIONS. The enclosure lid is held in place by a snap fit, in 4 places. In the approximate locations shown, insert small screwdriver between lid and base and pry outward to release snap fit.
  • Page 11 MT Tracker BBQ Operating Manual Place electronics board back into base. Pay attention to wire routing so that wires do not get pinched when lid is reassembled. Also check that the enclosure seal is properly seated into the base. Seal...
  • Page 12 MT Tracker BBQ Operating Manual 4. If Sync button came loose during disassembly, assemble button back to lid. Button will stay attached to lid once properly assembled to lid.
  • Page 13 MT Tracker BBQ Operating Manual 6. Place lid back into base and press down fully to reengage all 4 snap fits.

  • Page 14: Warranty

    MT Tracker BBQ Operating Manual Warranty The MT Tracker BBQ™ carries a 12 month warranty from the date of purchase. This warranty excludes apparent misuse of the sensor and battery.

  • Page 15: Safety Guidelines

    MT Tracker BBQ Operating Manual Safety guidelines Use of this device in a manner other than stated in this manual, may result in impairment of the designed safety protection and thus an unsafe condition.

  • Page 16: Specifications

    MT Tracker BBQ Operating Manual Specifications Specifications Part number GASM1001354 Measurement method Ultrasonic Fluid Cylinder types Steel cylinders Note: Also works with aluminum cylinders with alternate mounting. Not intended for use on composite cylinders. Cylinder sizes Vertical DOT Cylinders of 3.7 kg and 8.5 kg Typically any LPG cylinder up to 500 mm (20”) fluid height, on...

  • Page 17: Troubleshooting Tips

    LPG as it boils into gas. sensor will correct the problem. MT Tracker BBQ™ sensor is shipped in sleep mode If the bottom of the cylinder is dirty or rusty it will to preserve battery life. You must press the Sync need to be wiped clean of any debris first.
  • Page 18 970–988 Great South Road, Penrose, Auckland, New Zealand © BOC Limited 2018. BOC is a trading name of BOC Limited, a Member of The Linde Group. Reproduction without permission is strictly prohibited. Details given in this document are believed to be correct at the time of printing. Whilst proper care has been taken in the preparation, no liability for injury or damage resulting from its improper use can be accepted.

Table of Contents