Brodersen Customer Services Your satisfaction is our primary concern. Here is a guide to Brodersen customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.
Page 4
Because of Brodersen’s high quality control standards and rigorous testing, most of our customers never need to use our repair service. If a Brodersen product is defective, it will be repaired or replaced at no charge during the warranty period.
A 'Declaration of Conformity' statement to the above standards, and a list of auxiliary equipment used for compliance verification, is available on request. This product must be disposed of in accordance with the WEEE directive. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Version 05 and 30 (VDC Supply) Figure 8: Power supply wiring diagram Earth connects to PE conductor - wire as short as possible. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 13
All outputs are short-circuit, overload, overvoltage, over temperature and wrong connections protected. External Supply 10-30VDC Figure 10: Digital output wiring diagram Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 14
Figure 13: Analog input wiring diagram Note: The shield must be connected to the common terminal ( C ). Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 15
Input / Output Data carrier detect Input Receive data Input Transmit data Output Data terminal ready Output Signal ground Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 16
LocalBus RJ45 connector for Brodersen I/O expansion modules. The LocalBus provide also support also power supply to I/O Expansion modules. NOTE that load is limited to 600mA@12VDC. Consult data sheet for details. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
NOTE: DO NOT USE STANDARD PATCH OR NETWORK CABLE TO CONNECT I/O MODULES. IT WILL DAMAGE THE LOCALBUS INTERFACES ON BOTH THE RTU AND THE I/O EXPANSION MODULE. ONLY USED UCC-5xx CABLES. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
In the following pictures, some examples of displayed values and statuses on the LCD display are illustrated. Figure 19: Some examples of displayed values and statuses on the LCD Display Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
The SD Card is now safely in place again and you can mount and power up the RTU again. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
In general we recommend that you keep the RTU32S free from dust and moisture and periodically ensure the all ventilation holes are free and not covered by any means. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Need help?
Do you have a question about the RTU32S Series and is the answer not in the manual?
Questions and answers