Page 1
SWITCH SWP2 - 10MMF SWP2 - 10SMF Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manual do Proprietário Manuale di istruzioni Руководство пользователя 取扱説明書...
Page 2
à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. normalement ou est tombé. AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ. SWP2 Owner’s Manual...
Page 3
FCC requirements. Modifica- ference, which can be determined by turning the product tions not expressly approved by Yamaha may void your “OFF” and “ON”, please try to eliminate the problem by using authority, granted by the FCC, to use the product.
Page 4
If you intend to use the product in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. Location and connection • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
Page 5
If this occurs, contact your dealer or a Yamaha customer service center to have the backup battery replaced. The life span of the backup battery is approximately 10 years, but this may vary depending on the conditions of use.
Page 6
Open Source Software Used in this Product provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. • Please refer to Yamaha Pro Audio website for the details of licensing article. Model No.
Page 7
2 through 6 of this agreement shall continue in party to perform such actions. force even after the termination of this agreement. (3) The customer shall not modify, erase, or delete the Yamaha copyright indications that are included in the Software. 7. Separability...
Status Indicator Display LINK/ACT setting ..........14 STATUS setting ............14 VLAN setting ............14 OFF setting............14 Initializing the SWP2 Using the Web GUI to restore the factory settings ................14 Using the cold start command to restore the factory settings..............15 Entering the <I> (uppercase I) key during startup to restore the factory settings ........15...
Refer to the rack and/or fan unit manual for details. • Web GUI Use this to view or edit the settings of SWP2 units on the network from a web browser. Access the Web GUI from the Yamaha Audio Network Monitor.
Communication speed for a metal trunk connection on connections. When there are multiple networks of the SWP2’s VLAN preset B is 1 Gbps per cable. If differing types, setting up a VLAN allows a logically there is only one cable, and the total bandwidth...
Controls and Functions Front panel The explanation here is based on the SWP2-10MMF. 1 LAN ports 3 LED mode indicators These are etherCON (RJ-45) ports for connecting This indicates what the status indicators are showing. Ethernet cables (CAT5e or better is recommended).
Page 12
Dante, and use the VLAN 2 port for control signals. If the SWP2 starts up with DANTE settings, it operates using IGMP V3. In this case, if the network includes (*2) If you use setting C, connect the computer that is...
NOTE Insert the cable plug all the way until it locks in • If an external power supply is connected, the SWP2 will securely. operate normally when its internal power supply and the Press the latch button on the plug to disconnect the external power supply are on, as well as when only one is power cord.
Indicator Illumination Status CAUTION Lit green Link is established. (LINK) Do not turn off the power to the SWP2 during initialization. Flashing Data is being transferred. Otherwise, a malfunction may occur. Upper green (ACT)
Parity check None the factory settings Number of stop bits The SWP2 can be restored to its factory settings by Flow control Xon/Xoff entering an uppercase <I> when the SWP2 is starting up. This explanation uses the method of disconnecting Using a console cable, connect the SWP2 and reconnecting the power cord.
480 x 44 x 362 mm (18-7/8" x 1-3/4" x 14-1/4") Weight (excluding accessories) 4.5 kg (9.9 lbs) Accessories Power cord, Owner’s manual Option item PA-700 (AC adaptor) *1 The LED MODE button allows the PORT indicators to be switched between indicating LINK/ACT-SPEED, STATUS, or VLAN. SWP2 Owner’s Manual...
Page 18
XLR-4-32 type *1 These terminals support AutoMDI/MDI-X *2 Conforming cable: SWP2-10MMF: GI-type multi-mode fiber cables with a core diameter /cladding diameter of approximately 50 μm/ 125 μm. Maximum cable length: 300 m SWP2-10SMF: SM-type single-mode fiber cables with a core diameter /cladding diameter of approximately 9 μm/ 125 μm.
Page 19
Dimensions Unit: mm * The contents of this manual apply to the specifications as of the firmware Rev. 2.03.01. To obtain the latest manual, access the Yamaha website then download the manual file. SWP2 Owner’s Manual...
Page 21
Yamaha Music Gulf FZE Tel: +356-2133-2093 JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 PA52 Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan (For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany...
Need help?
Do you have a question about the SWP2 and is the answer not in the manual?
Questions and answers