1. Manuals
  2. Brands
  3. SENAO Manuals
  4. PCI Card
  5. PCE3500AH
  6. User manual

SENAO PCE3500AH User Manual

802.11 pcie module
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
802.11 an PCIe Module
PCE3500AH
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for SENAO PCE3500AH

Summary of Contents for SENAO PCE3500AH

  • Page 1 802.11 an PCIe Module PCE3500AH User’s Manual...
  • Page 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 3 The final end product must be labeled in a visible area with the following " Contains TX FCC ID: U2M-PCE3500AH ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules.

  • Page 4: Table Of Contents

    Table of Contents CHAPTER 1: INTRODUCTION ............1   EATURES ....................1  HYSICAL ETAILS ..................1  CHAPTER 2: INSTALLATION.............2   Install Software ......................... 2   Install Hardware........................ 2   Verification ......................... 2   CHAPTER 3: NETWORK CONNECTION .........3   OW TO AKE A ONNECTION ..............3 ...

  • Page 5: Chapter 1: Introduction

    Chapter 1: Introduction The Dual-band Wireless USB Dongle can access two different networks which could act in any WiFi station or AP combinations. Operating either in the Hz and 5GHz frequency bands, the Dual-band Wireless USB Dongle effectively increases the available wireless bandwidth and reduces wireless interference.

  • Page 6: Chapter 2: Installation

    Chapter 2: Installation Install Software Note: Do not insert the Wireless USB Adapter into the computer until the InstallShield Wizard finished installing. 1. Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM will run automatically. Please click Next to process the installation. 2.When the following screen appears, click Finish to restart the computer to complete the software installation.

  • Page 7: Chapter 3: Network Connection

    Chapter 3: Network Connection How to Make a Connection To make a connection with an access point, please follow below steps. Here takes Windows XP OS for example. Step 1: After set up the Wireless USB Adapter successfully, please launch the Configuration Utility.

  • Page 8: Chapter 4: Utility Configuration

    Chapter 4: Utility Configuration Station Mode Show Tray Icon: Check to show the wireless adapter icon at the tray. Disable Adapter: Check this to disable the wireless adapter. Radio off: Check this to turn OFF radio function. Windows Zero Config: Click to use windows built-in wireless utility. Close: Click to leave the Intelligent Wireless LAN Utility.
  • Page 9 Profile Tab Here shows a distinctive name of profile in this column. Profile Name The SSID is the unique name shared among all wireless access points in SSID the wireless network. Click Add button to add a profile from the drop-down screen. Profile Name: Users can enter profile name at will.
  • Page 10 mutual authentication of the client and the network. It relies on client-side and server-side certificates to perform authentication and can be used to dynamically generate user-based and session-based WEP keys to secure subsequent communications between the WLAN client and the access point. ...
  • Page 11 Shows the currently channel in use. Channel Shows the encryption type currently in use. Valid value includes WEP, Encryption TKIP, AES, None and TKIP/AES. Network Show the device network authentication. Authentication Shows transmit power, the amount of power used by a radio transceiver to Signal send the signal out.

  • Page 12: Switch To Ap Mode

    The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security setup and management of Wi-Fi networks. The STA as an Enrollee or external Registrar supports the configuration setup using PIN (Personal Identification Number) configuration method or PBC (Push Button Configuration) method through an internal or external Registrar.
  • Page 13 point. Channel: User can select the channel form the pull-down list. Wireless network security Network Authentication: There are several types of authentication modes including Open System, Shared Key, WPA-PSK and WPA2-PSK. Data encryption: For Open System and Shared Key authentication mode, the selection of encryption type is WEP.

  • Page 14: Chapter 5: Remove

    Rx Retry Shows information of packets failed transmit after hitting retry limit. Shows information of packets received with ICV error. Rx ICV Error Reset Click to reset counters to zero. This page displays setting Internet connection sharing (ICS). Select a sharing public network and click Apply button to make a connection.

Table of Contents