Related Manuals for Classic Eco1
Summary of Contents for Classic Eco1
- Page 1 Installation Installation & & Operators Manual Operators Manual Eco 1, 2, 3 Eco 1, 2, 3 H 500, 700, 750 H 500, 700, 750 Duo 2, 3 , 500, 750 Duo 2, 3 , 500, 750...
-
Page 2: Table Of Contents
Installation and Operation instructions Installation and Operation instructions For ‘Classic Glass & Dishwashing Systems’ under counter range of glass and dishwashers. Section Title Page(s) Safety instructions The appliance Installation 2 - 5 Commissioning 5 - 8 Operation 8 - 11... -
Page 3: Safety Instructions
WILL INVALIDATE ANY WARRANTY AND RELIEVE THE MANUFACTURER OF ALL LIABILITY Installation : Installation should only be carried out by a ‘Classic’ approved technician, and in accordance with current regulations and within our instructions. Modification : ‘Classic Glass & Dishwashing Systems Limited’ reserves the right to modify either the appliance or the contents of these instructions without notice. -
Page 4: The Appliance
Unpacking : Use suitable means and protective equipment to avoid injury whilst unpacking and handling the appliance. Remove all outer packaging and the protective film from the outer panels of the appliance prior to installation. Ensure all packing materials are disposed of in accordance with local regulations. - Page 5 3.2.1 Electrical rating : Within the ‘Classic’ range several of the 500mm² basket appliances can be either down rated or up rated electrically, such a procedure MUST be carried out by a ‘Classic’ approved technician.
- Page 6 Water connection : The appliance comes with a water supply hose requiring a ¾” BSP male threaded connection at the mains water supply, upon installation and commissioning all water joints must be checked for leaks). 3.3.1 Water supply restrictions : Water supply constraints must be adhered to : •...
-
Page 7: Commissioning
Gravity drain machine • Flexible waste hose must be securely attached to the waste outlet elbow on the rear of the machine. • The waste hose must flow down from the waste outlet elbow to the drain. • Ø35mm (Ø1 ¼”) stand- pipe required, must be lower than the baseline of the appliance... - Page 8 4.1.1 Rinse aid prime : • Switch machine ON and allow to fill • Remove the lower front panel (do not to touch any wire connections). • Depress and hold button located on the chemical pump bracket. • To fully prime, this will take approx 1 ½ minutes.
- Page 9 80° c Interlock options : Eco1,Eco2, Eco3, H500,H700 & H750 have the following four interlock options, all other under counter appliances do not have such options, to select such an option remove the front lower panel, towards the centre of the machine you will find four cables tied together, each wire with a different coloured cover (black, green, red &...
-
Page 10: Operation
Demonstration : ‘Classic’ recommends that prior to leaving the site / installation, the installer demonstrates the following to the end user, as this will ensure the appliance is correctly used • What to do in case of an emergency, i.e. how to isolate the mains electricity and water (see section 1). - Page 11 Prior to switching the machine ON, ensure that you are familiar with the controls on the front fascia of the appliance and the location of the isolator for mains electricity and water supply. Eco1,Eco2, Eco3, H500,H700 & H750 2 & 3 5 & 6 Duo2, Duo3, Duo500 &...
- Page 12 Starting a cycle : To start a cycle, open the door, load the first basket, ensuring that bottom and top wash arms will rotate freely, on Eco1, Eco2 and Duo2 appliances there are no top rotating wash arms. Close the door, then depress the ‘Cycle’ switch, your appliance will now auto...
- Page 13 Now isolate mains water and electricity at the wall. Drain pump appliances (optional on Eco1,Eco2) • Switch appliance OFF at fascia. • Remove drain plug from wash tank on Eco1, Eco2, H500, Duo2 & Duo500 models. • Close the door. •...
-
Page 14: Cleaning
Prior to cleaning : Switch off and isolated electrical supply before cleaning the appliance WARNING DO NOT use cleaning agents that contain CHLORINE, BLEACH or HYPOCHLORITE. DO NOT use STEEL WOOL, WIRE BRUSHES or any other abrasive materials. DO NOT jet wash or hose pipe the appliance down either internally or on the exterior Internal cleaning : Remove the wash arms from the appliance and... -
Page 15: Trouble Shooting
Exterior cleaning : Wipe the exterior of the appliance with a damp sponge (NOT WET) Once dry, clean using a STAINLESS STEEL cleaning agent • Before placing a service call , please check the following: • Check the appliance is connected to the mains water and electricity supply and both are turned on. - Page 16 7.2 Appliance fills slowly : • Check water supply tap is fully open. • Check water supply pressure, should be above 2 bar, if not ask your dealer to install a booster pump to increase water pressure. • Check and clean rinse jets (located on the wash arms within the appliance).
- Page 17 • If glasses are ‘Blooming’ you may need a water softener, call your dealer to advise on size of water softener required. • If a water softener is fitted, replenish the salt within the softener, as per the water softener instructions. 7.6 Overfilling : •...
- Page 18 Notes Notes ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ………………………………………………..........................................................................................................Page 16...
- Page 19 Affix Stamp C C C C S S S S D D D D L A S S I LA S S IC LA S S IC LA S S IC E RV ICE E RV ICE E RV ICE E RV ICE E P A RT ME N T E PA RT ME N T...
- Page 20 ‘Classic’ will supply a new tank free of charge. * Excludes operator or chemical misuse PRODUCT DETAILS The information you supply to ‘Classic’ is covered by the DATA PROTECTION ACT. This will also assist us to speed up MODEL NO SERIAL NUMBER the process, if you require a service visit.