Related Manuals for Dettson R02P032
Summary of Contents for Dettson R02P032
- Page 1 INSTALLATION INSTRUCTIONS AND HOMEOWNER’S MANUAL Communicating Thermostat Model : R02P032 Printed in Canada on 2019-03-04 X00493 Rev.B 100% recycled paper...
- Page 2 WHITE-RODGERS HOMEOWNER HELPLINE: 1-800-284-2925 Thermostat features: • Programming for any schedule (including non-programmable) • Reminders for seasonal maintenance and changing filters • Energy saving features that improve comfort • Thin profile with sharp color display FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL AND SYSTEM COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE.
-
Page 3: Table Of Contents
Table of Contents Thermostat Overview 1.1 Display and Controls ............... . . 1.2 Navigating through the menus . -
Page 4: Thermostat Overview
Thermostat Overview Display and Controls 1. The indoor temperature 2. The relative indoor humidity 3. The day of the week and the time 4. The outside temperature if outdoor sensor is connected 5. The desired temperature or setpoint 6. Indicates system setting or 7. -
Page 5: Navigating Through The Menus
Navigating through the menus Your thermostat features a simplified easy to understand menu structure. Navigating through any menu in your thermostat uses the same approach. • Press to enter the Main Menu The Main Menu lists the menus that access and set thermostat operating options and programming. -
Page 6: Installation
2 Installation This booklet contains installation instruction and information on the thermostat only. Separate installation instructions for the furnace or air handler and outdoor AC condensing unit or heat pump are provided. This thermostat is designed exclusively for the ClimateTalk communicating system. -
Page 7: Installing Thermostat
Installing Thermostat • Carefully separate the thermostat body from the thermostat base. • Place base at installation location and mark mounting hole locations on wall using base as a template. • Move base out of the way. Drill mounting holes. •... -
Page 8: Check Système Operation
Messages at Thermostat As equipment is found on the network, the display will show, “device” Found. Searching icon will show until all equipment is found and configured. If no equipment is found on the network after approximately five minutes, the home screen will appear and indicate a Fault. - Page 9 3. Press to adjust thermostat setting above room temperature. The cooling system should stop operating. Fan Operation 1. Press FAN button until Fan On is displayed. The fan should begin to operate. 2. Press FAN button to change the display to Fan Auto. The fan should stop operating as long as there is no call for heat or cool.
-
Page 10: Thermostat Setup And Usage
Thermostat Setup and Usage Set Time and Date • Press to enter the Main Menu. • On the Main Menu, highlight and enter Clock and Display Settings. • Highlight and Enter Time & Date. • Set the time and date using the buttons. -
Page 11: Auxiliary Heating (Heat Pumps Only)
Auto Changeover is used where both heating and cooling may be required during the same day. AUTO allows the thermostat to automatically select heating or cooling depending on the indoor temperature and the selected heat and cool temperatures. This thermostat will not allow you to program a conflict between Heating and Cooling setpoints. -
Page 12: Permanent Temperature Hold
Permanent Temperature Hold If you desire, you can set your thermostat to permanently hold a temperature. This feature will bypass any programs you may have set in your thermostat and maintain a single constant temperature. Note: This mode is recommended at all times. To use Permanent Hold, change the temperature with and press the Hold button. -
Page 13: Display Settings
When a reminder appears, it can be turned off by entering the Alert Information Detail menu on the Main Menu. Select Yes to “Clear Alert and Reset Timer”. Display settings In addition to setting time and day on this menu, you can use the Display Settings menu to adjust the screen brightness, choose the background color, select the keypad backlight, and the auto dimmer. -
Page 14: Heating Program/Cooling Program
Heating Program/Cooling Program On the Main Menu, highlight and enter Heating Program or Cooling Program. Refer to section 4. 3.10 Fan Settings Menu This menu selects the speed that the fan will run when selected On with the Fan button. Enter Fan “On”... -
Page 15: Thermostat Settings Menu
3.11 Thermostat Settings Menu Additional thermostat operating settings are found in the Thermostat Settings Menu. On the Main Menu highlight and enter Thermostat Settings Filter Maintenance/UV Lamp Maintenance Humidifier Maintenance Default for each is Off. When set to On, a maintenance reminder will appear on the home screen when the system has run for the selected amount of time. - Page 16 Auto Humidity Reduction Default is Off. When selected High or Low provides the ability to minimize or reduce the window condensation by reducing the humidity setpoint when the outside temperature is cold. Optimum – Comfort or Dehum Default is Off. When Comf option is selected the temperature is altered by the humidity to reflect the true comfort.
- Page 17 Humidity Setpoint Humidity setpoint is the percent humidity that the heating system and humidifier will attempt to maintain in heating mode. Default for Humidity Setpoint is 45%. Adjust the humidification setpoint to a value from 20% to 50%. De-Hum Setpoint The Dehumidification setpoint is the percent of humidity that the cooling system will try to reach.
-
Page 18: Programming The Thermostat
Programming the thermostat Note: It is recommended to disable the programming feature (section 3.5), or to program the same temperature for every hour of every day to optimize the comfort and efficiency of the system. Energy Saving Factory Pre-Program The thermostat is programmed from the factory with the energy saving settings shown below for every day of the week. -
Page 19: Entering The Heating & Cooling Programs
Entering the Heating & Cooling Programs Entire Week program illustrated below. Entering Heating Program Entering Cooling Program • On the Main Menu, highlight and enter After entering Heating Program, press Heating Program highlight Switch to Cool Program and press • Highlight and enter Entire Week , or enter Cooling Program on the Main •... -
Page 20: Diagnostics
5 Diagnostics Alert Info Detail If the thermostat senses trouble with a component of your system (the heat pump, air handler, furnace or air conditioner), or a maintenance reminder appears, an alert will be displayed on the Home screen. Details of any alert can be found on the Alert Info Detail menu in the main menu. -
Page 21: Modulating Chinook System Fault Codes
Modulating Chinook System Fault Codes Display Code Diagnostic Description Display Code Diagnostic Description Long Run Time Low press. switch closed (inducer off) System Pressure Trip Low press. switch open (inducer high) Short Cycling Low press. switch open (inducer low) 4 (L4) Locked Rotor High press. -
Page 22: Advanced Installer Menu
Advanced Installer Menu This menu allows the installer to check installer-specific information or set advanced settings. It is accessible from the Home screen when the buttons are pressed at the same time for three seconds. Select the items using the buttons and press the button to enter the item to view information or change settings. -
Page 23: Equipment User Menu
Dual Fuel Setpoint Similar to the Heat Pump Disable option, but with gas heat. As long as the outside temperature is above the Dual Fuel Setpoint, the compressor will operate. When the temperature drops below the setting, the thermostat will start the gas heat and shut off the compressor. - Page 24 Chinook Gas Furnace User Menus Main Menus Status Used to display equipment information Fault History Display info. on last 6 error codes 2 Week History Display operating info. of last 2 weeks Life History Display total operating info. Unit Info Display model and serial numbers Setup Adjustable settings...
- Page 25 Life History Parameter Indications Comments Total Days Pwrd XXXX Total days control has been powered Lo HT Hrs XXXXXX Low Heat Hours of Operation Lo HT Cycles XXXXXX Low Heat Cycles Hi HT Hrs XXXXXX Low Heat Hours of Operation Hi HT Cycles XXXXXX Low Heat Cycles...
- Page 26 Dehum Parameter Indications Comments Dehum Ratio 80-90 % CFM in dehumidification Active Low No , Yes If DH input is active-low Parameter Indications Comments Cont Fan Ratio 0-100, FC* % CFM when fan on Rise 20-80, FC* Temperature rise (°F) Autobackup Parameter Indications...
-
Page 27: Record Of Thermostat Options
Record of Thermostat Options For your quick reference, below are the options selected by your installing dealer to optimize your equipment settings and your personal home comfort preferences. (Contractor to fill in value or check box.) Thermostat Options Configuration Menu Default Air Filter Maintenance ___ Months... - Page 28 Notes...