Related Manuals for HIKVISION DS-FB52 Series
Summary of Contents for HIKVISION DS-FB52 Series
- Page 1 Explosion-proof Dome·Quick Start Guide Explosion-proof Dome Quick Start Guide UD04569B...
- Page 2 DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
- Page 3 Explosion-proof Dome·Quick Start Guide USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
- Page 4 Explosion-proof Dome·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 5 Explosion-proof Dome·Quick Start Guide Hazardous Area Classification: Zone 1, Zone 2, Zone 21, Zone 22 IP Degree: IP68 (2m, 2h) Ex Standards: IEC 60079-0: 2011 EN 60079-0: 2012 IEC 60079-1: 2014 EN 60079-1: 2014 IEC 60079-31: 2013 EN 60079-31: 2014 Special Conditions for Safe Use °C °C...
- Page 6 Explosion-proof Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.
- Page 7 Explosion-proof Dome·Quick Start Guide Do not place the speed dome in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. ...
-
Page 8: Table Of Contents
Explosion-proof Dome·Quick Start Guide Table of Contents 1 Overview ...................... 8 1.1 Explosion-proof Speed Dome Overview ..............8 1.2 Explanation of model naming .................. 8 1.3 Power Consumption ....................9 1.4 Explosion-proof Parameters ..................9 1.5 Mechanical Specification ..................9 1.6 Working Environment .................... -
Page 9: Overview
Explosion-proof Dome·Quick Start Guide 1 Overview 1.1 Explosion-proof Speed Dome Overview The explosion-proof speed dome captures high quality colored images in dim light environment with its low illumination and offers more details over expansive areas. It is equipped with explosion-proof enclosure made of stainless steel. It can be widely used in places such as: port, wharf, petrochemical industry, military industry. -
Page 10: Power Consumption
Explosion-proof Dome·Quick Start Guide Figure 1-3 Product Naming Rule 2 1.3 Power Consumption For detailed information about the power supply voltage or power consumption, refer to Explosion-proof Speed Dome Nameplate. 1.4 Explosion-proof Parameters For detailed information, refer to Explosion-proof Performance Certification. 1.5 Mechanical Specification ... -
Page 11: Installation
Explosion-proof Dome·Quick Start Guide 2 Installation 2.1 Preparation 2.1.1 Basic Requirement All the electronic operation should be in strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. -
Page 12: Cable Description
Explosion-proof Dome·Quick Start Guide 2.2 Cable Description Power Cord RS-485 Cable CVBS Cable Alarm Cable Audio Cable Optical Fiber Network Cable Figure 2-1 Cable Description Notes: The cables vary depending on different models of the speed dome. 2.3 Installing the Explosion-proof Speed Dome Before you start: Check the package contents and make sure that the device in the package is in good... -
Page 13: Wall Mounting
Explosion-proof Dome·Quick Start Guide Cutting off the Cable Head Do not cut off the optical fiber head Figure 2-2 Cutting off the Cable Head Note: Keep the cable head you cut off and you need to weld it back after installation. 2.3.2 Wall Mounting Before you start: ... - Page 14 Explosion-proof Dome·Quick Start Guide Cable Outlet Unit:mm Figure 2-3 Install the Installation Plate 3. Route the cables into the bracket body. Insert three preassemble screws into the preassemble screw holes on the cable joint (do not tighten the preassemble screws) as shown in Figure 2-4.
- Page 15 Explosion-proof Dome·Quick Start Guide Three Fixing Screws Three Preassemble Screws Figure 2-6 Secure the Speed Dome 6. Install the bracket to the installation plate. 1) Hang the safety rope to the speed dome and the hook on the bracket. 2) Route the cables of the speed dome through the bracket and connect the corresponding cables.
-
Page 16: Pendant Mounting
Explosion-proof Dome·Quick Start Guide 2.3.3 Pendant Mounting Before you start: Make sure the ceiling is thick enough to withstand the expansion screws. Make sure the ceiling must be strong enough to withstand more than eight times the weight of the dome and its accessories. ... - Page 17 Explosion-proof Dome·Quick Start Guide Bracket Slots Figure 2-11 Rotate the Bracket 5. Screw three fixing screws into the fixing screws holes on the bracket. Then tighten three preassemble screws to secure the speed dome as shown in Figure 2-12. Three Fixing Screws Three Preassemble Screws Figure 2-12 Secure the Speed Dome 6.
-
Page 18: Cable Entry Installation
Explosion-proof Dome·Quick Start Guide Explosion-proof Junction Box (Optional) Figure 2-14 Secure the Bracket 8. Tear off the protective film on the bubble after the installation is finished. 2.3.4 Cable Entry Installation Purpose: To ensure the explosion-proof performance of the speed dome, you shall route the cable through the cable entry to protect the cables after speed dome installation. -
Page 19: Power-Up Action
Explosion-proof Dome·Quick Start Guide Sealing Ring Washer Gland Nut Figure 2-16 Seal the Cable Entry 3. Weld the cables heads back. 2.3.5 Power-up Action Make sure all cables are connected properly. Then power on the device to perform the power-up action. The device does self-test actions automatically, and then you can get the live view and check whether the PTZ control can work normally. -
Page 20: Setting The Dome Over The Lan
Explosion-proof Dome·Quick Start Guide 3 Setting the Dome over the LAN Notes: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection. If the product does not work properly, contact with your dealer or the nearest service center. -
Page 21: Activation Via Sadp Software
Explosion-proof Dome·Quick Start Guide 2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface. Note: The default IP address of the speed dome is 192.168.1.64. Figure 3-2 Activation Interface(Web) 3. -
Page 22: Modifying The Ip Address
Explosion-proof Dome·Quick Start Guide Figure 3-3 SADP Interface 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. - Page 23 Explosion-proof Dome·Quick Start Guide 2. Click to select an active device. Note: Refer to Section 3.2 Activating the Speed Dome to activate the speed dome if it is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
-
Page 24: Accessing Via Web Browser
Explosion-proof Dome·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome8 and above version... - Page 25 Explosion-proof Dome·Quick Start Guide Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, refer to the user manual of network speed dome.