Procedures Before Washing; 洗衣前的準備 - Panasonic NA-F60A6P Operating Instructions Manual

(NA-F60A6)
■ To connect external drain hose.
外部排水膠管連接方法。
External drain hose
外部排水膠管
Hose band
膠管的固定環
Drain hose connection
連接頭
Connect the drain hose securely to the main
body of the washer.
將排水膠管牢靠地連接至洗衣機本體上。
(請確認膠管不會脫落，否則有漏水的可能。）
Drain hose connection External drain hose
連接頭 外部排水膠管
Move the hose band next to the washer body.
將膠管的固定環移至洗衣機邊上。
Hose band
膠管的固定環
Drain hose connection External drain hose
連接頭 外部排水膠管
Make sure to remount the back panel after
changing the position of the drain hose.
When the external drain hose is difficult to install,
please coat with washing liquid in the inside of the
hose.
If extended external part is necessary when connecting the drain hose
·The length of the drain hose should be less than 3 m and the height below 10 cm. Otherwise the machine will
stop running while in operation.
·Be sure the distance between the machine and the wall is above 5 cm.
如要延長外部排水膠管,連接排水膠管時
其長度應在3 m以內，高度在10 cm以下，若太長或太高，運轉途中會停機。
·
· 本機與墻壁之間應保留5 cm以上的空間。
10
■ Changing the drain hose to the opposite
side (left).
將排水軟管移至相反一側(左側)。
Remove the back panel.
拆除後蓋板。
Back panel
後蓋板
Remove the left hose hole cover.
拆除左側的孔蓋。
Hose hole cover
孔蓋
Remove the right screw, move the interior drain
hose from the right to the left, and fasten with
the screw .
拆除右側的螺釘，將內部的排水軟管從右側移至左
側，並再用螺釘固定好。
Install the hose hole cover to the right hose hole,
and fasten with the screw.
將孔蓋裝到右側並用螺釘固定。
Install the back panel, and fasten with the screw.
裝好後蓋板並用螺釘固定。
在變更排水軟管位置以後，務須安裝好後蓋板。
外部排水膠管不容易裝入時，請在膠管的內側涂上
洗滌液。
MAX. 3 m
3 m以下

Procedures before Washing

洗衣前的準備
·Check the installation
See page 8 for details.
Attach the drain hose to drain.
Connect the water supply hose.
Turn on the water faucet.
Note
Be sure to close the water faucet after the operation.
Plug the cord into outlet.
Be sure to pull the power plug out of the outlet
after the operation.
(Only for NA-F60A6P)
(僅對 NA-F60A6P 而言)
■ Detection of the amount of laundry
Put the laundry into the machine.
放入衣物。
Press the power OFF/ON button
and then press the START button
after putting in the laundry.
放入衣物後，按電源"關/開"和
開始鈕。
In"SPEEDY" Course and "DELICATE" Course, the laundry load is not measured.
Attention
MAX. 10 cm
注意 "超快速"程序和"纖細衣物"程序不進行衣物量檢測。
10 cm以下
■ When washing laundry's lint gets off easily, please raise the water level to advance the rinsing
effect.
■ 洗滌容易脫落線屑的衣物時，請適當提高水位高度，以提升漂洗效果。
·確認安裝狀況
詳細情況請參照第8頁。
接好排水膠管使其處於排水狀態。
連接供水膠管。
打開水龍頭。
注意
使用完畢後請確認關閉水龍頭。
將插頭插入插座。
使用完畢後請確認將電源插頭從插座中拔出。
■ 衣物量檢測
Allow the machine to churn Water level is indicated.
the laundry for 8 seconds.
顯示水位。
It will indicate the appropriate water
洗衣機攪拌衣物約8秒。
The pulsator rotates for about level ( except 17L). Add the
8 seconds without any water indicated amount of detergent.
in the tub to measure the
顯示與現有衣物量相應的水位
amount of laundry.
(17L除外)。根據顯示加入洗滌劑。
洗衣槽在無水的情況下，旋轉
葉輪約8秒來檢測衣物量。
11