Checking.the.battery.level; Installation; Installation.on.your.bike; Installing.sensors - Pioneer SGX-CA500 User Manual

Cyclocomputer
Hide thumbs Also See for SGX-CA500:
Table of Contents

Advertisement

To power up
Press.the.[START/STOP].button.for.more.than.2.seconds.
to.turn.on.the.device.for.use.
Press.the.[START/STOP].button.for.more.than.2.seconds.
again.to.turn.off.the.device..Charging.time.is.shorter.if.the.
device.is.turned.off.
•. It.takes.about.4.hours.to.charge.fully.(normal.charging)..The.
device.will.automatically.stop.charging.once.the.battery.is.
100%.fully.charged.
•. When.the.device.is.turned.off,.the.screen.turns.dark.after.5.
seconds..Touch.the.touch.panel.to.check.the.battery.level.
•. For.the.sake.of.safety,.the.device.will.not.charge.when.outside.
the.temperature.range.of.0°C-40°C..When.the.device's.internal.
temperature.is.too.high,.full.charge.may.not.be.achieved..In.this.
case,.turn.off.the.device,.allow.time.to.cool.down.and.recharge.
•. Connect.the.provided.USB.cable.directly.to.a.USB.port.of.
your.PC..If.the.device.is.connected.via.a.USB.hub,.it.may.not.
charge.to.full.capacity..Make.sure.that.the.USB.output.of.your.
PC.accepts.5V/1000mA.
•. Do.not.unplug.the.USB.cable,.shut.down.the.PC.or.use.sleep.
mode.while.the.device.is.transferring.data.as.it.may.corrupt.the.
data.in.the.device.
4. Unplug the USB cable from the USB port.
Once.data.transfer.is.complete.and.the.battery.is.fully.
charged,.disconnect.the.USB.cable.from.the.PC.first,.then.
from.the.device.
5. Close the USB connector cover.
To.ensure.water.resistant.performance,.firmly.close.the.
USB.cover.
Checking the Battery Level
You.can.check.the.battery.level.with.the.battery.icon.on.the.
status.bar.of.the.home.screen.and.the.menu.screen.
•. When.the.battery.is.running.low.on.power,.a.warning.screen.
will.appear.“Battery.Level.Decreasing.”.If.not.recharged,.the.
device.will.shut.down.automatically.
•. You.can.also.check.the.remaining.battery.charge.using.the.
[System].item.of."Cyclocomputer.Settings."
A.fully.charged.battery.can.run.for.approximately.12.hours.
(brightness.5).
•. Operating.time.may.vary.depending.on.the.operating.
conditions.
•. If.the.operating.time.is.abnormally.short,.the.battery.may.need.
to.be.replaced..For.details,.please.visit.our.website.

Installation

Installation on Your Bike
Mount.the.Cyclocomputer.on.your.bike.
•. When.you.mount.the.Cyclocomputer.on.your.bike,.be.sure.your.
bike.is.in.a.stable.position.to.prevent.it.from.falling.
1. Remove the bolt from the bracket.
Remove.the.bolt.from.the.bracket.using.a.3.mm.hex.
wrench.
•. Be.careful.not.to.lose.the.removed.bolt.
2. Make sure that the lever on the bracket is pushed
towards the bolt's direction.
3. Mount the bracket on the handlebar of your bike.
•. Be.careful.not.to.pinch.your.finger.when.mounting.the•.bracket.
on.the.bike.
4. Secure the bracket with the bolt.
Apply.anti-seize.compound.like.a.grease.to.the.bolt.
Adjust.the.bracket.horizontally.from.the.stem,.insert.the.
bolt.into.the.hole.and.tighten.lightly.
5. Attach the strap to the device.
Lace.the.strap.through.the.lanyard.hole.for.the.strap.
6. Attach the device to the bracket.
Fasten.the.strap.to.the.handlebars..Set.the.tip.of.the.
bracket.in.the.bracket.slot.on.the.device.and.push.the.
device.until.it.clicks.
7. Push back the lever on the bracket to secure the
device to the bracket.
8. Adjust the angle of the device, and then tighten
the bracket.
If.the.device.is.not.aligned.to.the.center.of.the.handlebars.
or.not.horizontal.to.the.stem,.loosen.the.bolt.and.realign.
the.bracket.
After.adjusting.the.angle,.clamp.the.temporary.joint.bolt.
and.tighten.the.bracket.
Use.a.tool.that.can.measure.the.torque.to.tighten.the.bolts.
Tightening.torque:.1.2.N·m
To detach the device
To.detach.the.device.from.the.handlebar.mount,.push.the.lever.
on.the.bracket.towards.the.bolt's.direction.and.lift.the.device.
Installing Sensors
This.device.is.compatible.with.ANT+™.sensors.mounted.on.
your.bike.
Refer.to.the.user's.manual.of.your.ANT+.sensors.for.mounting.
instructions.
After.mounting.a.sensor,.perform.pairing.with.the.device.
For.details,.refer.to."Pairing.Sensors".in.the."Basic.Operations".
chapter.of.this.manual.
This.product.is.ANT+™.certified.
Visit.http://www.thisisant.com/directory/.for.a.list.of.compatible.
products.and.apps.
Page 5

Advertisement

Table of Contents
loading

Table of Contents