CognitiveTPG A798 Setup Manual page 2

3
Choose a location for the printer.
4
Connect the following cables based on your configuration, using a-b below.
Connector
Interface
When using USB (step "b" below),
Panel
use caution to ensure the USB
cable is connected to the USB
connector on the back left of
the printer and not into the
cash drawer connector that is
USB
Connector
on the back right of the printer.
a
Cash drawer (if your installation includes this feature, page 15).
b
9-pin or 25 pin Serial or USB cable (serial: page 16; USB: page 17).
c
Connect the power cable (page 18).
d
Route cables as shown for your setup configuration (page 19).
Communication
Connector
Cover Connector
(RS-232C 9-pin)
(Closed)
(Route straight
out back of
printer and
tighten screws)
USB Power Supply
Cable Strain Relief
5
Run a diagnostic test (page 19).
Open
Cover
Power Cash Drawer
Supply Cable
Connector Strain Relief
CAUTION:
DO NOT plug the
USB Cable here.
RS-232C Communication Cash
Connector Drawer
(9-pin shown) Connector
Power
USB Cable
Supply
Strain Relief
Cable
(Straight
Power Supply
back)
Strain Relief
USB
Cable
Cash Drawer
Cable
Back of
Printer
USB Cable
Strain Relief
Push and hold
Paper Feed Button
while closing Cover
6
Configure the printer if necessary (page 20).
*** A798 – Diagnostics Form ***
Model number : A798-720D-TD00
*** A795 - Diagnostics Form ***
Serial number : C073400014
Model number : A795-2119
Boot Firmware
Revision Serial number : V3.04 : A012251287
CRC : 74D1
P/N : 189-798B304A
Boot Firmware
Flash Firmware
Revision : V1.02
Revision : V3.01
CRC : 76EB
CRC : 4FFF
P/N : 189-1076076A
P/N : 189-7940497A
Flash Firmware
Revision : V1.13
H/W parameters
CRC : AB62
Flash Memory Size : 2 Mbytes
P/N : 189-7950290A
Flash Logos/Fonts : 1152 kbytes
Flash User Storage : 64 kbytes
H/W parameters
Flash Perm'nt Fonts : 0 kbytes
Flash Memory Size : 2 Mbyte
Flash Journal Size : 64 kbytes
Flash Logos/Fonts : 1024 kbytes
SRAM Size : 128 kbytes
Flash User Storage : 0 kbytes
Head setting : C
SRAM Size : 256 kbytes
Pre-Heating : Disabled
Head Setting : D
Print Density : 100%
Paper Type Name : Type 5, Version 0
Max Speed : 150 mm/sec
Color Density Adj : 100 %
Paper Width : 80 mm
Max Power Print Density (Mono) : 55 W : 100 %
Knife Max Speed : Enabled : 100 mm/sec
Partial Cut : 125 steps
Paper Width : 80 mm
Paper Low Sensor Max Power : Disabled : 55 W
Knife : Enabled
Comm. Interface
Partial Cut : 135 steps
RX Buffer Size : 4096
Paper Low Sensor : Disabled
Interface type : RS232/USB
Parameters
Comm. Interface
Baud Rate : 115200
RX Buffer Size : 4096
Data Bits : 8
Interface type : RS232/USB
Stop Bit : 1
Parameters
Parity : NONE
Baud Rate : 115200
Flow Control : DTR/DSR
Data Bits : 8
Reception Errors : Ignore
Stop Bit : 1
USB Driver Type : Printer Class
Parity : NONE
USB Packet w/Error : Reject
Flow Control : DTR/DSR
Reception Errors : Ignore
Resident Code Pages : 437, 850, 852, 858
Alternate DTR/DSR : Disabled
860, 863, 865, 866
1252, 862, 737, 857
Resident Code Pages 1251, 1255, KZ-1048 : 437, 850, 852, 858
860, 863, 865, 866
Logo(s) defined : YES
1252, 862, 737
User Char(s) defined : NO
Journal Unused : 64 kbytes
Available Paper Types : 00.00 01.00 05.00
01.90 01.92 01.93
Logo (s) defined : YES
To enter Printer Config Menu :
User Char(s) defined : NO
1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down
To enter Printer Config Menu :
1) Flip DIP switch #1 down
DECLARATION OF CONFORMITY
2) Reset the printer, while holding
Model: A798-XXXX-XXXX
the Paper Feed button down
Model: A799-XXXX-XXXX (X = any alphanumeric character)
CognitiveTPG, LLC, 950 Danby Road, Ithaca, New York, 14850
This declaration of conformity is issued under the sole responsibility of the Manufacturer: CognitiveTPG, LLC
Information Technology Equipment – Thermal Printer
The object of the declaration described above is in conformity with Directive 2011/65/EU of the European Parliament and
of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic
equipment. With the exception of models A798-XXXP-XXXX and A799-XXXP-XXXX
Applicable EU Directives:
2004/108/EC (electromagnetic compatibility directive)
2006/95/EC (low voltage directive for product safety)
Harmonized Standards:
EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect to the
restriction of hazardous substances
EN 55024:2010 Information Technology Equipment Immunity Characteristics
EN 55022:2010/AC:2011 EMC, Class B, Limits and Methods of Measurement of Interference
Characteristics of IT Equipment
EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011
IEC 60950-1 (ed.2);am1- Product Safety Standard.
Signed for and on behalf of CognitiveTPG, LLC
Ithaca, NY, March 20, 2013
Jeffrey C Phoenix, Regulatory Compliance Engineer, CognitiveTPG, LLC Ref #: 189-1300058 Rev K
********* **********
MAIN MENU
*******************************
Select a sub-menu :
- EXIT -> 1 click
- Print Current Configuration -> 2 clicks
- Set Communication Interface -> 3 clicks
- Set Diagnostics Modes -> 4 clicks
- Set Emulation/Software Options -> 5 clicks
- Set Hardware Options -> 6 clicks
- Set Paper Type -> 7 clicks
Enter code, then hold Button DOWN
at least 1 second to validate
When the printer is configured for USB, this
location will show either: "USB Driver Type:
Printer Class", or "USB Driver: Comm Class".
Print Test and Configuration Menu Sample.
Samples will vary depending on the printer model.
Current Printer tallies are
}
printed after the Diagnostic
information and will vary
per printer use.