JWM WM-5000P5+ Specification

(gps+rfid) guard tour system
Hide thumbs Also See for WM-5000P5+:

Advertisement

Quick Links

WM-5000P5+ (GPS+RFID)
Guard Tour System
Specification

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WM-5000P5+ and is the answer not in the manual?

Questions and answers

Summary of Contents for JWM WM-5000P5+

  • Page 1 WM-5000P5+ (GPS+RFID) Guard Tour System Specification...
  • Page 2: Table Of Contents

    Contents 2. Safety Cautions.............. - 5 - 3 Product Overview ............- 6 - 3.1 Packaging ..............- 6 - 3.2 Appearance and Structure ........- 6 - 3.3 Press Key Instruction ...........- 7 - 3.4 Charging ..............- 8 - 3.5 SIM card installation..........- 9 - 4 Operational Flowchart..........
  • Page 3 AnnexⅠ Product and Accessories Introduction . - 28 - 1. Reader ...............- 28 - 2. USB Communication cable .........- 28 - 3. RFID Tag (sold separately) ........- 29 - 4. Charger ..............- 30 - Ø - 3 -...
  • Page 4 Ø Functions and additional services might be different according to device, software or service provider. Copy Right © Shenyang JWM Hi-Tech Development Co.,Ltd 2012. All Rights Reserved. Shenyang JWM High-Tech Development Co., Ltd. written consent, any unit or individual will be allowed to extract and copy part of the contents of this instruction or transmitted in any form.
  • Page 5: Safety Cautions

    Always operate device in accordance with the regulations, instructions and signs in potentially explosive environment. Ø Do not use device near flammable materials, chemicals places or explosive region. Shenyang JWM Hi-Tech Development Co.,Ltd Address:No.22 Shiji Road, Hunnan National Hi-Tech Industrial Zone, Shenyang city, China Tel: 0086 24 31681066/31681067/31681068/31681069...
  • Page 6: Product Overview

    3 Product Overview 3.1 Packaging a standard package should have items as below: Ø 1 piece WM-5000P5+ reader Ø 1 piece of USB communication cable Ø 1 piece of charger Ø 1 piece of hex wrench Ø 1 piece of holster 3.2 Appearance and Structure 1、3G LED (green), GPS&RFID LED(red) 2、power LED(blue)
  • Page 7: Press Key Instruction

    6、Reset Key 7、RFID tag reading area 8、Open and insert SIM card 9、USB port for communication and charging. 3.3 Press Key Instruction Power on/off key: Ø Power on: Press On/Off key for 1 second, Power light starts flash, after 1 second, device vibrates once(vibrates twice in collection mode),then light goes out.
  • Page 8: Charging

    “Send” Key: Ø “Send” key: Time interval for touching “Send” key is 1s~9s, and device defaults as 2s. Ø In collection mode, touch “Send”key for 2 seconds, device will vibrates once and start to collect GPS site. Ø In patrolling mode,touch “send”key for 2 seconds, device will vibrates once and start to send patrol data.
  • Page 9: Sim Card Installation

    3.5 SIM card installation Step1: use hex wrench manufacturer provide to open back cover as picture below. Step2: insert SIM card to slot,put metallic contact inward and chamfer side is at bottom left. It should be as the picture below after installation. Step3: fasten the SIM card slot, and screw on back cover.
  • Page 10: Operational Flowchart

    Operational Flowchart - 10 -...
  • Page 11: Basic Function

    5 Basic Function 5.1 Product Profile WM-5000P5+ intelligent guard tour system adopts world-leading GPS(Global Positioning System) and RFID technologies. Sending patrol information(guards, longitude&latitude, and RFID tag’s site, event, time) through 3G network real-time, It can be used to monitor and supervise the guard who need to take long-distance patrol in many fields.
  • Page 12 RFID (Radio Frequency Identification) is the use of a wireless non-contact system that uses radio-frequency electromagnetic fields to transfer data from a tag attached to an object, for the purposes of automatic identification and tracking. WM-5000P5+ supports RFID tag reading function, the RFID tag we produced is small-sized, damage resistent and waterproof.
  • Page 13 advance, control center displays guard's patrol route and guard’s current location etc... in real time. Ø Fixed checkpoint patrol: If the checkpoint is important and need guard to spend time to make a detailed check, you can use this function. WM-5000P5+ adopts GPS+RFID mixed patrolling, you can use GPS function at places where are not very convenient to install RFID tag, and use RFID tag reading function at places where there is no GPS signal(eg.
  • Page 14 11. Alarm Manually “SOS” key is specially designed for guard who need to patrol alone or patrol at remote areas. Guard can press “SOS” key to send alarm message to control center for help anytime and anywhere. 12. Records Storage Capacity Ø...
  • Page 15: Basic Settings

    6 Basic settings It consists of 6 digits, which is used to identify the Device number device. It is used to clear all data in the device, such as guard Device initialization names, GPS locations, RFID check points, and collection data. It is used to clear up all patrol data (patrol data, alarm Device data...
  • Page 16 (under the patrol mode) Alarm button Under the patrol mode, setup the time for pressing the settings button to send alarm data - 16 -...
  • Page 17: Site Collection

    7 Site Collection 7.1 Site Collection Setup Taking stand-alone version software as example Install patrol management software on control center’s server at first, for details, please take software instruction for reference. After installation, connect device with server by USB cable, and do setups as below: Ø...
  • Page 18 take software instruction for reference. Ø Device can collect 1500 unknown sites at most(GPS site and RFID checkpoint), when records are full, device will vibrate 3 times when collect new site, and this data will not be saved. - 18 -...
  • Page 19: Patrol

    8 Patrol 8.1 Patrol setup Taking stand-alone version software as example connect device with server by USB cable, and do patrol setups as below: for details, please take software instruction for reference. Ø Server’s IP address or domain name, DNS setup. Ø...
  • Page 20 twice after reading RFID tag. Sending patrol records manually: In this mode, data will be saved in device, and only be sent when guard press “Send” key to connect with 3G network Send patrol records automatically. In this mode, after guard arrives GPS fixed checkpoint or read a RFID tag, device will connect with 3G network and send data automatically 2.
  • Page 21 Sending patrol records manually. In this mode, data will be saved in device, and only be sent when guard press “Send” key to connect with 3G network Send patrol records automatically. In this mode, device will connect with 3G network and send data automatically when there is tracking records.
  • Page 22: Data Sending

    9 Data Sending 1. Send data manually: In manual mode, data will be saved in device, press “Send” key to send data, device vibrates once and 3G LED is still on, start to send data. Ø Sending data successfully, device vibrates once, 3G LED will be off after it flashes 5 times.
  • Page 23 alarm data. Ø Sending successfully, device vibrates once, 3G LED is off after it flashes 5 times. Ø Sending failed, device vibrates 3 times, 3G LED is off. Notice: device is under low power status, device will send low power alarm data when it is turned on.
  • Page 24: Status Alert

    10 Status Alert Status Alert power on under collection blue led long light,2 vibrations mode power on under patrol blue led long light,2 vibrations mode power off blue led long light, vibrates every second standby blue led lights every second low power blue led flashes twice every 3 seconds charging...
  • Page 25 Arrive in GPS location red led flashes 5 times and 1 vibration Data storage is coming to 5 vibrations maximum capacity Data storage is full vibrates 6 times every 5 seconds - 25 -...
  • Page 26: After-Sale Services

    11. After-sale Services When we handed this qualified excellent system to you, in fact our service has just started. We will provide you with excellent training administrator, technical service at any time, in order to make sure you have operated the system properly.
  • Page 27 Ø Due to the user or the third part’s negligence, abuse, misuse, malicious damage or damage caused by evil. Ø User dismantle the device without approval from JWM( any incorrect change that may cause damage) Ø Connection to inappropriate accessory, use without working manual, product’s damage caused by transport and other accident.
  • Page 28: Annexⅰ Product And Accessories Introduction

    Annex Ⅰ Product and Accessories Introduction 1. Reader GPS Positioning ≤10 meters Precision ≤33s Cold boot ≤1s Hot boot ≥3.5cm Reading range 2000mAh/3.7v polymer Battery lithium battery Working time (for 30 hours one full charge) (sending data every 70S) communication USB/GSM/3G Working -40℃~+85℃...
  • Page 29: Rfid Tag (Sold Separately)

    YD/T1019 , IEC61156 , ANSI/EIA/TIA-568 Standard three cable standards Low transferring return loss; continuous insulation consistency; anti electromagnetic Features interference which makes a lower rate of transferring mistake Delay 5.02 ns/m Impedance 107–11Ohm Return loss 26.0dB 3. RFID Tag (sold separately) Function Read only Memory...
  • Page 30: Charger

    Luminous tag: 76mm×56mm round shape tag: Dimensions Ф30mm×4.5mm nail shape tag: Ф6.5mm×28mm Weight About 2g 4. Charger Input AC 100V-250V 50-60 Hz voltage Output DC 4.2V voltage Output 1000mA current - 30 -...
  • Page 31 FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types A208 (FCC ID: RRB-WM-5000GT) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use is 0.204W/kg. This device was tested for typical body-worn operations with the back of the handset kept 1.0cm from the body.

Table of Contents