Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Costar CDI2528W
Summary of Contents for Costar CDI2528W
- Page 1 Network Camera Installation Manual...
- Page 2 Before reading this manual This is a basic installation manual for use of a network camera. Users who are using this product for the first time, as well as users with experience using comparable products, must read this operation manual carefully before use and heed to the warnings and precautions contained herein while using the product.
- Page 3 Before reading this manual Safety Precautions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Important Safeguards 1.
- Page 4 Before reading this manual Warning: This product emits infrared light. Do not look into the IR LED. FCC Compliance Statement THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
-
Page 5: Table Of Contents
Table of Contents Part 1 – Introduction ......... 6 Product Features . -
Page 6: Part 1 - Introduction
Part 1 – Introduction Product Features • IP filtering, HTTPS, SSL, IEEE 802.1X, and configurable user authority levels for greater security • Network bandwidth limitation and MAT features for This camera is an IP-based network camera that more efficient use of network bandwidth compresses and transmits video over ethernet. -
Page 7: Accessories
Accessories Upon purchasing the product, check inside the box to make sure all the following accessories are included. External appearances and colors of the accessories may vary depending on the model. Network Camera Screws, Anchors (2 ea.) Guide Pattern Quick Guide... -
Page 8: Overview
Part 1 – Introduction Overview Body Product color and design may vary depending on the IR LED non-supported model model. Dome Cover IR LED supported model Side Cable Access • Side Cable Access Hole For routing cables. - Page 9 Part 1 – Introduction The table below shows the network cable specifications. IR LED <The network cable specifications> Lens Item Content Note Factory Reset Button Connector RJ-45 Wall/Ceiling Installation Hole 10/100 Ethernet 10/100 Base Mbps Bottom Cover UTP Category 5e or Cable Network Port higher...
-
Page 10: Factory Reset
Part 1 – Introduction Installation Factory Reset Only use the factory reset button to restore the camera Installation of this product does not require the use of to its factory default settings. special tools. For more information on other devices comprising the A factory reset will clear all camera settings configured overall system, refer to their respective installation by the user. -
Page 11: Inserting A Sd Memory Card
Part 1 – Introduction Inserting a SD Memory Card Insert a SD memory card into the SD memory card slot with the 'micro SD' print facing upward. Push the SD memory card until it disengages from the slot, and then pull it out. Installation •... -
Page 12: Closing The Dome Cover
Part 1 – Introduction Closing the Dome Cover • Horizontal Rotation Used to adjust the lens' horizontal angle. Turn the horizontal rotator in the clockwise or counterclockwise direction. Attach the dome cover to the bottom cover. Turn the dome cover clockwise to fasten the dome cover. Dimension 111.9mm (4.4") Angle Adjustment... -
Page 13: Part 2 - Camera Connection
Part 2 - Camera Connection Use the camera by connecting to DirectNET™ NVR or non DirectNET™ NVR, VMS such as INEX Basic. With DirectNET™ NVR-based Layout Power Network Camera Monitor Out Power Network Remote Monitoring DirectNET™ NVR makes it easy to use cameras without extra network configurations. Each camera can be controlled via the DirectNET™... -
Page 14: With Non Directnet™ Nvr-Based Layout
Part 2 - Camera Connection With non DirectNET™ NVR-based Layout Network Camera Network microSD Memory Card Remote Monitoring (INEX Basic or WebGuard) Remote Recording (INEX Basic) Control the camera over the network from software installed on a computer. The contents in the camera operation manual are only for users using the camera with non DirectNET™ NVR connection or VMS connection such as INEX Basic. -
Page 15: Part 3- Appendix
Part 3- Appendix Troubleshooting Problem Check The main unit won't turn • Check the power cable connection. • Check the power outlet. PoE switch isn't being Check the grounding status of the I/O device connected to the camera and the PoE recognized. -
Page 16: Specifications
Part 3- Appendix Specifications These product specifications may change without prior notice. Video Image Sensor 1/3” CMOS Max. Resolution 1920 x 1080 Scanning Mode Progressive Scan Lens type Fixed-focal Focal Length f=4.0mm/f=2.8mm Aperture F2.0/F1.8 Iris Control Fixed Iris Angular Field of View H: 80.3°... - Page 17 Part 3- Appendix General Operating Temperature -10˚C ~ 50˚C (14˚F ~ 122˚F) -10˚C ~ 45˚C (14˚F ~ 113˚F) (IR LED ON) Boot Up Temperature 0˚C ~ 50˚C (32˚F ~ 122˚F) Operating Humidity 0% ~ 90% Power Source PoE (IEEE 802.3at Class 2) Power IR LED Supported Max.
Need help?
Do you have a question about the CDI2528W and is the answer not in the manual?
Questions and answers