Page 1
All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any form or by any means to persons not employed by a Eurotherm group company without written permission from Eurotherm Drives Ltd.
Page 2
Eurotherm Drives warrants the goods against defects in design, materials and workmanship for the period of 12 months from the date of delivery on the terms detailed in Eurotherm Drives Standard Conditions of Sale IA058393C. Eurotherm Drives reserves the right to change the content and product specification without notice.
Page 6
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#5##7HFKQLFDO#6SHFLILFDWLRQ IMPORTANT: 3% line impedance MUST be provided for each module, and is assumed in the quoted input current values. Failure to do so will severely curtail DC link capacitor lifetime and could result in damage to the input bridge Input current quoted is for 380V supply at the stated motor power.
Page 7
The choke should not saturate at the peak instantaneous current level specified. This value accommodates the 150% overload condition. For complete details refer to the following Eurotherm Drives drawings included in Appendix A:- HL463115C Rating Specification for HPAC AC Line Choke...
Page 8
*HQHUDO *HQHUDO The Model 584S/620 Type 8, 9 and 10 Series provide Class 10 Motor Overload Protection. The maximum internal overload protection level (current limit) is 150% for 60 seconds for Model 584S/620 Series (Industrial Ratings) and 110% for 10 seconds for Model 584S Series (HVAC Ratings).
Page 9
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#5##7HFKQLFDO#6SHFLILFDWLRQ 6KRUW#&LUFXLW#5DWLQJ Suitable for use on a circuit capable of delivering not more than 100000 RMS Symmetrical Amperes, 460V maximum. )XVH#5HSODFHPHQW#,QIRUPDWLRQ The fuses provided on Switch-Mode Power Supply Printed Wiring Board (see Chapter 9) must be replaced with those manufactured by Bussmann, Type HVR, or equivalent, rated 2A, 1000V dc.
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#6##3URGXFW#&RGH &KDSWHU#6##3URGXFW#&RGH All 584S and 620 units are fully identified using an eleven block alphanumeric code. This code details the drive calibration and settings on despatch from the factory. The product code appears as the "Model No." on the rating label at the side of the unit.
Page 12
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#6##3URGXFW#&RGH 8;762953...
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#7##7URXEOHVKRRWLQJ &KDSWHU#7##7URXEOHVKRRWLQJ In addition to the diagnostics provided by the opstation, eight fault LEDs situated on the power control board provide an indication of the cause of a fault trip. The fault LEDs are visible when the bottom terminal cover is removed - refer to Figure 1.1.
Page 14
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#7##7URXEOHVKRRWLQJ The suggested course of action in response to the diagnostic LED alarms is summarized in table 4.2: 7DEOH#715 )$8/7 $&7,21 04#SKDVH#RYHUFXUUHQW 2XWSXW#FXUUHQW#JUHDWHU#WKDQ#WULS#OHYHO1#&KHFN#RXWSXW#ZLULQJ 05#SKDVH#RYHUFXUUHQW DQG#PRWRU#IRU#LQVXODWLRQ#EUHDNGRZQ#RU#VKRUW0FLUFXLWV#HLWKHU 06#SKDVH#RYHUFXUUHQW EHWZHHQ#SKDVHV#RU#EHWZHHQ#SKDVH#DQG#HDUWK1 04#SKDVH#,*%7#IDXOW#DODUP ([FHVVLYH#RXWSXW#FXUUHQW1 05#SKDVH#,*%7#IDXOW#DODUP 0D[LPXP#,*%7#MXQFWLRQ#WHPSHUDWXUH#H[FHHGHG#0#FKHFN...
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#8##0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ &KDSWHU#8##0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ $LUIORZ The size 8, 9 and 10 of the 584S and 620 Series utilize very large airflows and have been designed with specific airflow patterns within a cabinet. Generally it is intended that the bulk of the air comes into the cabinet at the top, flows down (some going through the drive to maintain internal temperatures), into the main cooling fan, through the drive, the brake/exhaust duct (supplied), and finally out the top of the cabinet through vent assembly (supplied).
Page 16
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com 0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ##&KDSWHU#8 8#0#5 8;762953...
Page 17
This manual was downloaded on www.sdsdrives.com &KDSWHU#8##0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ +44 (0)117 938 1800 - info@sdsdrives.com Size 10 Typical Cubicle Installation Outline Drawing (HG 463009 G 001) 8;762953 8#0#6...
Page 18
This manual was downloaded on www.sdsdrives.com &KDSWHU#8##0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ +44 (0)117 938 1800 - info@sdsdrives.com Size 9 Typical Cubicle Installation Outline Drawing (HG 463009 G 002) 8;762953 8#0#7...
Page 19
This manual was downloaded on www.sdsdrives.com &KDSWHU#8##0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ +44 (0)117 938 1800 - info@sdsdrives.com Size 8 Typical Cubicle Installation Outline Drawing (HG 463009 G 003) 8;762953 8#0#8...
Page 20
This manual was downloaded on www.sdsdrives.com &KDSWHU#8##0HFKDQLFDO#5HTXLUHPHQWV#IRU#&DELQHW#0RXQWLQJ +44 (0)117 938 1800 - info@sdsdrives.com 8;762953 8#0#9...
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#9##)LWWLQJ#7RS#9HQW#DQG#*DVNHW &KDSWHU#9#)LWWLQJ#7RS#9HQW#DQG#*DVNHW Warning! This unit must be operated with either a brake unit or blanking plate fitted to the supplied outlet duct. The top vent is then mounted on to the outlet duct. It is very important that the gasket for the vent is correctly fitted to the exhaust/brake outlet duct.
Page 22
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#9##)LWWLQJ#7RS#9HQW#DQG#*DVNHW 9#0#5 8;762953...
Page 23
This manual was downloaded on www.sdsdrives.com &KDSWHU#9##)LWWLQJ#7RS#9HQW#DQG#*DVNHW +44 (0)117 938 1800 - info@sdsdrives.com Size 10 Typical Cubicle Machining (HG463010 G 001) 8;762953 9#0#6...
Page 24
This manual was downloaded on www.sdsdrives.com &KDSWHU#9##)LWWLQJ#7RS#9HQW#DQG#*DVNHW +44 (0)117 938 1800 - info@sdsdrives.com Size 9 Typical Cubicle Machining (HG 463010 G 002) 9#0#7 8;762953...
Page 25
This manual was downloaded on www.sdsdrives.com &KDSWHU#9##)LWWLQJ#7RS#9HQW#DQG#*DVNHW +44 (0)117 938 1800 - info@sdsdrives.com Size 8 Typical Cubicle Machining (HG 463010 G 003) 8;762953 9#0#8...
Page 26
This manual was downloaded on www.sdsdrives.com &KDSWHU#9##)LWWLQJ#7RS#9HQW#DQG#*DVNHW +44 (0)117 938 1800 - info@sdsdrives.com 9#0#9 8;762953...
Page 27
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#:##)LWWLQJ#5HPRWH#2SHUDWRU#6WDWLRQ#9533 &KDSWHU#:##)LWWLQJ#5HPRWH#2SHUDWRU#6WDWLRQ#9533 The type 8, 9,and 10 584S and 620 series drives are designed to allow use of a remote mounted operator station. This is available as a kit Model Number 6200 and may be fitted to the outside of a cabinet. It replaces the drive mounted Operator Station.
Page 28
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#:##)LWWLQJ#5HPRWH#2SHUDWRU#6WDWLRQ#9533 9. Connect supplied cable to the operator station (note the cable is not symmetric and the end marked “OP Station” must be attached to the drive board). &XWRXW#'LPHQVLRQV )LJXUH#:15 :#0#5...
Page 29
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#;#7\SH#;/#<#DQG#43#,QYHUWHU#%UDNH#8QLW#,QVWDOODWLRQ &KDSWHU#;##,QYHUWHU#%UDNH#8QLW#,QVWDOODWLRQ#*XLGHOLQHV 29(59,(: Type 8, 9 and 10 brake units are optional. It is however, possible to retro-fit a brake unit (ONLY if drive was shipped ON OR AFTER 9-12-96) should the need arise. There are three brake units, one for each drive frame size.
Page 30
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#;#7\SH#;/#<#DQG#43#,QYHUWHU#%UDNH#8QLW#,QVWDOODWLRQ Remove drive top cover which is attached via 4 off M5 screws on the side and 2 off M5 screws on the top. Care should be taken to keep the cover from falling into the drive and damaging the internal components.
Page 31
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#;#7\SH#;/#<#DQG#43#,QYHUWHU#%UDNH#8QLW#,QVWDOODWLRQ )LJXUH#;05##9LHZ#ZLWKRXW#%UDNH#&RQQHFWLQJ#3ODWH+V,#VKRZLQJ#WKH#&RQWURO#&DEOH FRQQQHFWLRQ#EHWZHHQ#WKH#%UDNH#8QLW#DQG#WKH#,QYHUWHU )LJXUH#;06#7RS#9LHZ#RI#([KDXVW#'XFW2%UDNH#8QLW2,QYHUWHU#$VVHPEO\#VKRZLQJ#WKH#%UDNH &RQQHFWLQJ#3ODWH+V,#DQG#6QXEEHU#&DSDFLWRUV#ILWWHG 8;762953...
Page 32
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#;#7\SH#;/#<#DQG#43#,QYHUWHU#%UDNH#8QLW#,QVWDOODWLRQ 8;762953...
Page 33
6(59,&,1* The 584S/620 type 8, 9 and 10 range of inverters have been designed to be serviceable units. In the unlikely event of component failure, it is possible to replace the faulty item without having to replace the complete drive unit.
Page 34
7\SH#< /$7973;58335 /$7973;68335 /$7973;58435 /$7973;68435 7\SH#43 /$7973;58336 /$7973;68336 /$7973;58436 /$7973;68436 35,17('#&,5&8,7#%2$5'6 The printed circuit boards listed below are common within the 584S/620 type 8, 9 and 10 range of inverters. 'HVFULSWLRQ 3DUW#1XPEHU 3DUW#1XPEHU +'ULYH#EXLOG#VWDQGDUG#?533, +'ULYH#EXLOG#VWDQGDUG#!533, 6ZLWFK#0RGH#3RZHU#VXSSO\#3&% $+6;<4998434 $+7977:58434 3RZHU#&RQWURO#3&% $+6;<49:8334 $+7977:48334 /LQH#6XSSUHVVLRQ#3&%...
Page 35
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<###0DLQWHQDQFH#DQG#6HUYLFLQJ &20321(17#5(3/$&(0(17 ,QWURGXFWLRQ Having identified the faulty component part and taken delivery of replacement part(s) the following replacement procedure should be carefully adhered to. WARNING : FAILURE TO FOLLOW PROCEDURE MAY RESULT IN DAMAGE TO THE INVERTER AND POSSIBLE ELECTRICAL SHOCK HAZARD! PERSONNEL PERFORMING COMPONENT REPLACEMENT PROCEDURES MUST BE ELECTRICALLY COMPETENT AND POSSESS THE KNOWLEDGE /EXPERTISE...
Page 36
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<####0DLQWHQDQFH#DQG#6HUYLFLQJ 35,17('#&,5&8,7#%2$5'#+3&%,#5(3/$&(0(17 Observe all electrical warnings and static handling precautions at the front of this section - ‘Component Replacement’ 3URFHGXUH 3RZHU#&RQWURO#3&%/#&$/,%5$7,21#FDUG#DQG#&RQWURO#3&%#+8;762953,#5HSODFHPHQW 3RZHU#&RQWURO#3&%/#&$/,%5$7,21#FDUG#DQG#&RQWURO#3&%#+8;762953,#5HSODFHPHQW1 1 1 1 3RZHU#&RQWURO#3&%/#&$/,%5$7,21#FDUG#DQG#&RQWURO#3&%#+8;762953,#5HSODFHPHQW 3RZHU#&RQWURO#3&%/#&$/,%5$7,21#FDUG#DQG#&RQWURO#3&%#+8;762953,#5HSODFHPHQW Remove drive top and bottom terminal cover (plastic) via 2 off ¥ turn fasteners at top and bottom of drive (see figure 1.1).
Page 37
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<###0DLQWHQDQFH#DQG#6HUYLFLQJ 6036#3&%#5HSODFHPHQW 6036#3&%#5HSODFHPHQW 6036#3&%#5HSODFHPHQW 6036#3&%#5HSODFHPHQW Follow steps 1 to 3 of procedure ‘Power Control PCB, CAL card and control PCB replacement’. Release hinged panel fixing - 1 off ¥ turn fastener as shown in figure 9.1. The SMPS PCB may now be viewed on reverse side of hinged panel as shown in figure 9.2.
Page 38
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<####0DLQWHQDQFH#DQG#6HUYLFLQJ /LQH#6XSSUHVVLRQ#$+6;<4<5#3&%#5HSODFHPHQW /LQH#6XSSUHVVLRQ#$+6;<4<5#3&%#5HSODFHPHQW /LQH#6XSSUHVVLRQ#$+6;<4<5#3&%#5HSODFHPHQW /LQH#6XSSUHVVLRQ#$+6;<4<5#3&%#5HSODFHPHQW Remove drive top and bottom terminal cover (plastic) via 2 off ¥ turn fasteners at top and bottom of drive. (see figure 1.1). Disconnect 30-way op-station ribbon cable from power control PCB CON 10 (see figure 9.1).
Page 39
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<###0DLQWHQDQFH#DQG#6HUYLFLQJ )$1#5(3/$&(0(17 Observe all electrical warnings and static handling precautions at the front of this section - ‘Component Replacement’. It is possible to replace the drive main cooling fan should the need arise. Having replaced the main cooling fan, ensure that the wiring loom routing/fixing is preserved.
Page 40
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<####0DLQWHQDQFH#DQG#6HUYLFLQJ Disconnect supply cable at faulty fan. Replace fan. Reconnect supply cable. Re-fit lower panel assembly. J. W . F . <#0#; 8;762953...
Page 41
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<###0DLQWHQDQFH#DQG#6HUYLFLQJ 3+$6(#$66(0%/<#5(3/$&(0(17 The inverter power stage consists of 3 identical phase assemblies. Each phase assembly consists of heatsink, IGBT module, 1/3 of the input bridge, DC link capacitors and PCB ‘AH389193’. It is intended that the whole phase assembly be carried as a spare part and replaced as a unit.
Page 42
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<####0DLQWHQDQFH#DQG#6HUYLFLQJ 3KDVH#$VVHPEO\#5HSODFHPHQW#3URFHGXUH 3KDVH#$VVHPEO\#5HSODFHPHQW#3URFHGXUH 3KDVH#$VVHPEO\#5HSODFHPHQW#3URFHGXUH 3KDVH#$VVHPEO\#5HSODFHPHQW#3URFHGXUH Replace any badly distorted heatsink clamps with spare clamps provided. (Clamps used in packaging). Carefully slide replacement phase limb assembly into position making sure that the studs on the input busbars (left-hand side) located in the holes provided on the phase limb busbar.
Page 44
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com &KDSWHU#<####0DLQWHQDQFH#DQG#6HUYLFLQJ <#0#45 8;762953...
Page 45
13. Packaging: suitable for delivery to Eurotherm Drives’ Goods In Department without any damage. 14. Unit to display rating label which will include Eurotherm Drives part number to be approved by Eurotherm Drives Ltd. 15. Design should be rated to IP00 (optional IP20) 16.
Page 46
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com...
Page 47
10 inverters. Refer to base product manual for more EMC information. (0&#),/7(56#72#5('8&(#/,1(#&21'8&7('#12,6( The 584S/620 type 8, 9 and 10 industrial drives can be supplied with filters to meet the ‘industrial’ Class A conducted emission limits of EN55011 when used with 300m of screened motor cable and the specified 3% minimum AC line choke as listed below:- 7DEOH#%14##$XSSO\#)LOWHU#DQG#/LQH#&KRNH#3DUW#1XPEHUV#IRU#&RQIRUPDQFH#ZLWK#(188344#&ODVV#$1...
Page 48
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com $SSHQGL[#%#(0&#DQG#)LOWHU#,QVWDOODWLRQ )LJXUH#%05##)LOWHU#0RXQWLQJ#'HWDLOV#8VLQJ#4#RII#3DUW#1R1#&279784:#IRU#7\SH#; 433PP#[#753PP##'((3 584 S SERIES (8527+(50 '5,9(6 958#PP HEALTH LOCAL BRAKE WARNING AVERTISSEMENT $&#/,1(#&+2.( ),77('#%(7:((1 ),/7(5#)#'5,9( 3$57#121#&26;<<698534#7; 3$57#121#&26;<<698535#7< )LJXUH#%06##:LULQJ#'HWDLOV#8VLQJ#4#RII#3DUW#1R1#&279784:#IRU#7\SH#; &+2.( )LOWHU &279784: 8;762953 /2$' /,1( /LQH 7;2<243 %#0#5 8;762953...
Page 49
/2$' /,1( NOTE: For 584S/620 type 8, 9 and 10 the specified EMC line choke in table B-1 must still be fitted between the 584S/620 and its filter. This is to ensure reliability of both filter and drive. 8;762953# %#0#6...
63(&,),&$7,21#2)#$&+,(9$%/(#(0&#(0,66,216 584S/620 type 8, 9 and 10 drive modules with the option to be ‘CE’ marked meet the following EMC emission limits, provided they are installed with the specified EMC filters, and line chokes as shown in table B1 and in accordance with the EMC installation instructions.
Page 51
(&#'(&/$5$7,21#2)#&21)250,7< In accordance with the EEC Directive 89/336/EEC, Article 10 and Annex 1, (EMC DIRECTIVE) We Eurotherm Drives Ltd, address as below, declare under our sole responsibility that the following electronic products 584S/620 Std/Link/Com (Type 8, 9 & 10) when installed and used in accordance with the instructions in the product manual (provided with each piece of...
Page 52
0$18)$&785(56#(0&#'(&/$5$7,21 In accordance with the EEC Directive 89/336/EEC, Article 10 and Annex 1, (EMC DIRECTIVE) We Eurotherm Drives Ltd, address as below, declare under our sole responsibility that the following electronic products 584S/620 Std/link/Com (Type 8, 9 & 10) when installed and used in accordance with the instructions in the product manual (provided with each piece of...
Page 53
In accordance with the EEC Directive 73/23/EEC and amended by 93/68/EEC, Article 13 and Annex III, (LOW VOLTAGE DIRECTIVE) We Eurotherm Drives Limited, address as below, declare under our sole responsibility that the following Electronic Products 584S and 620 Std/Link/Com (Type 8/9/10)
Page 54
8th April 1999 ........................Dr Dan Slattery, Dr Martin Payn, Date Technical Director Conformance Officer Eurotherm Drives Ltd Eurotherm Drives Ltd (8527+ (50#' 5, 9(6#/,0,7(' 1(:#&2857:,&.#/$1(/#/,77/(+$0 3721/#:(67#6 8 6 6 (;#% 14:#:5= 7(/(3+21(=#34<36#:6:333###)$;=#34<36#:6:433 5HJLVWHUHG#QXPEHU=##448<;:9#(QJODQG1##5HJLVWHUHG#2IILFH=##6RXWKGRZQYLHZ#:D\/#:RUWKLQJ/##:HVW#6XVVH[#%147#;11 ‹#4<<<#(8527+(50#'5,9(6#/,0,7(' )LOH#1DPH=#3=?+3$&?'2&6?0$18$/?,668(B;?$33(1'B&1:5' ,66= '$7( '51= 03&...
Page 55
This manual was downloaded on www.sdsdrives.com +44 (0)117 938 1800 - info@sdsdrives.com $SSHQGL[#& 6XSSO\#+DUPRQLF#$QDO\VLV constant torque load and stated nominal motor output Assumptions: 90-280kW: 18,000A short circuit supply capability, power. * 315kW: 30,000A short circuit supply capability. ∑ Q THD(V) x 100 = h 40 where Q is the rated rms value of the fundamental voltage of the supply transformer.
Need help?
Do you have a question about the 584S/620 and is the answer not in the manual?
Questions and answers