Related Manuals for Efitment IC007
Summary of Contents for Efitment IC007
- Page 1 Belt Drive Indoor Cycling Bike: IC007 PLEASE READ THIS MANUAL CAREFULLY BEFORE USING THE BIKE. For Customer Service, please contact: service@efitment.com...
- Page 2 IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly.
- Page 3 EXPLODED VIEW 1...
- Page 4 EXPLODED VIEW 2 75 76 77 75 76 77 63 64...
- Page 5 PARTS LIST Description Qty. Description Qty. Main frame Screw M8*16 Rear stabilizer Arc washer d8*Φ20*R16*2 Foot pad Φ43*14*M8*25 Front post Nut M8*H5.5*S1 Grommet End cap PT60*30*20 Handlebar Screw M8*40*20*S6 Spring washer d8 Washer d8*Φ16*1.5 Sensor wire 1 Round end cap Φ25*16 Front stabilizer Nylon nut M6*H6*S10 Sensor pad...
- Page 6 Description Qty. Description Qty. Flywheel Inductor GrommetΦ12*11*Φ3 Bearing 6000-ZZ SpacerΦ16*10.2*16 Inertial axle Screw ST4.8*10*Φ8 Φ10*165*M10*1.0*43*33 Flywheel cover...
- Page 7 HARDWARE PACKAGE...
-
Page 8: Main Frame (
ASSEMBLY INSTRUCTIONS STEP 1: Fix the Front stabilizer (8) and the Rear stabilizer (2) onto the Main frame (1) with Screws (6) and Washers (7). - Page 9 STEP 2: A. Push the Brake handle (23) into the Main frame (1) down slowly and then fix it with the Screw (39) and Washer (32). B. Lock the Pedal (12L/R) on the *left and right crank of the Main frame (1).
-
Page 10: Saddle Post 1
STEP 3: A. Fix the Saddle (22) onto the Saddle tube (21) with Washers (19) and Nylon nuts (18). B. Insert the Saddle post (15) into the Main frame (1), and then lock it with the Knob (13). C. Put the Saddle tube (21) on the Saddle post (15), and then tighten using the Knob (16) and Washer (17). -
Page 11: Front Post
STEP 4： A. Connect the Lower sensor wire (48) with the Upper sensor wire (46), then push the connected sensor wire back into the tube of Main frame (1). B. Fix the Front post (42) on the Main frame (1) with Arc washers (41), Washers (7) and Screws (40). -
Page 12: Handlebar
STEP 5： A. Assemble the Handlebar (44) on the Front post (42), and fix it with Screws (40), Spring washers (45) and Washers (7). B. Insert the Computer (50) onto the support of the Handlebar (44) and then connect the Sensor wire (46) to the Computer (50). Assembly is now complete. - Page 13 Notice: Push down the knob to enforce brake, and stop the bike immediately. Rotate the knob clockwise to increase the resistance. Rotate the knob counter- clockwise to decrease the resistance.
- Page 14 USAGE AND MAINTENANCE 1. If there is no signal coming to the computer, please check if the sensor wires (46&48) are connected correctly. 2. If the display becomes blurry, please replace the batteries to improve the result. 3. This bike can be leveled to compensate for uneven surfaces. To level the bike, please raise or lower the foot pads, which are located on the bottom of the front and rear stabilizers.
- Page 15 EXERCISE COMPUTER SPECIFICATIONS: TIME -------------------------------------------------------00:00 -- 99:59 MIN: SEC SPEED ----------------------------------------------------0.0 – 999.9 ML/H DISTANCE -----------------------------------------------0.00 – 99.99 ML CALORIES -----------------------------------------------0.0 – 999.9 KCAL KEY FUNCTIONS: MODE: Press to select function. (Time, Speed, Distance, Calories). -Press and hold the mode button for three seconds to reset time, distance and calories. OPERATION PROCEDURES: 1.
Need help?
Do you have a question about the IC007 and is the answer not in the manual?
Questions and answers