If the auger stops during juicing Before requesting a repair Product specifications EUJ-828 ( For Household Use Only / Warranty Included ) 01 Read the instructions carefully before using. 02 Keep these instructions somewhere easily accessible. 03 Use only with 230-240 V AC power supply.
Safety precautions Do not plug or unplug with wet hands. • It may cause electric shock or injury. Only use 230 - 240V AC power. • Incorrect voltage may cause electric shock or fire. Motor damage can occur with incorrect voltage. Plug in the power cord correctly and push it firmly in a power outlet.
Page 5
Safety precautions • If the auger stops rotating while juicing, press [REV] button and hold for 2-3 seconds. Release the button and wait for the auger to completely stop, then press [ON] button again. If the juicer is overloaded and continues to stop, the parts may become damaged and performance may be reduced due to overheating of the motor.
Parts and accessories 02 Rotating brush 01 Hopper Side hopper Feeding tube chute Silicon brushes Brush holder Safety sensors 03 Auger 04 Juicing Chamber Screw axis Mid gear Juice outlet 05 Pusher Pulp outlet Juice cap seal Lever Juice cap 06-08 Strainers 07 Coarse Strainer...
Page 7
Parts and Accessories 11 Base Safety Sensor Body bumps Motor Operating switch axle 12 Cleaning Brush...
How to disassemble the juicing chamber Please clean all parts before first use. Turn the hopper counterclockwise and pull it up. Disassemble by lifting the strainer and rotating brush from the chamber. Pull out the auger holding it by both sides. Disassemble the rotating brush and strainer.
How to prepare produce / Strainer types How to prepare ingredients for juicing Apple · Pear · Kiwi · Juice produce like pear, kiwi, cucumbers, etc. with the seeds and skin. However, apple Cucumber seeds can be toxic in large amounts, so it is better to remove them. Separate each grape from the cluster.
How to assemble for juicing STEP STEP Assemble the strainer and spinning brush Insert the auger into the strainer. as shown in the picture.
Page 11
How to assemble for juicing STEP STEP Place the assembled parts from [STEP 2] After putting the hopper on the chamber, into the chamber by turning the strainer turn it clockwise until it is locked com- from side to side to fit the groove in the pletely.
How to assemble for making ice cream STEP STEP Insert the auger into the ice cream Insert the ice cream strainer into the strainer and turn it from side to side chamber. Align the ice cream outlet until it fits in. with the juice chamber outlet.
Page 13
How to assemble for making ice cream STEP After putting the hopper on the chamber, turn it clockwise until it is locked completely. Note The juicer can be operated with the hopper assembled in either direction.
How to use : For juicing / ice cream Set the lever to the [ ] position CLOSE before operating. The juicing chamber will not attach properly if the control lever is not in the [ CLOSE] position. Press [ON] button to start.
How to use control lever by mode The control lever is located between the juice cap and pulp outlet. The control lever regulates the back-pressure of pulp and can improve juice yield ] Preparation·Juicing CLOSE For general ingredients, the extraction rate is best when you close [CLOSE] the lever during operation.
How to use control lever according to ingredients Use the control lever according to the characteristics of each ingredient to make a more delicious juice. When you extract over 400ml at once, please open Note the control lever every 400ml to release the pulp. The hopper can’t be opened during juicing or it may cause damage when the pressure in the chamber increases.
How to clean Cleaning the parts Unplug the power cord with dry hands after the unit has completely stopped. Remove the juicing chamber from the main body. Twist the chamber cover to open and lift up the parts in order to disassemble the unit. Using the cleaning brush, wash the parts under running water.
Page 20
How to clean Juice cap gasket Open the juice cap, hold the juicing chamber and juice cap with one hand, and remove the juice cap gasket with your other hand. Wash with warm soapy water. Please be careful not to drop or damage the juice cap and juicing chamber when disassembling the unit.
Precautions while juicing Ingredients which require special attention - Fruits with hard seeds or pits such as persimmon, Japanese apricot, lemon, plum, peach etc. that are hard to chew with our teeth must have their pits removed before juicing. - Stalk vegetables with strong fibers such as water parsley and celery should be cut into small lengths about 3-4 cm before juicing.
If the auger stops during juicing ► The juicer may stop if ingredients are forced in or inserted too quickly. ► Always insert ingredients slowly and let the juicer self feed. Press [REV] for 3 - 5 seconds to release pressure from the auger.
Before requesting a repair 02 Please make sure the line on the 01 The main body will not work by itself. hopper is properly aligned with the body For your safety, this unit only works when main body is correctly assembled with the For your safety, this juicer will only operate when the hopper is properly aligned.
Page 24
Before requesting a repair When calling for service, please have the manufacturer’s serial number or bar code available. 07 Do not insert too many ingredients 08 Only use the pusher when feeding at once. ingredients. Other objects will damage the juicer. If you insert an excessive amount of ingredients or improperly cut ingredients, the unit may stop.
Product Specifications / Warranty Product Specifications Product Name Sana Slow Juicer Cord Length 1.4 m EUJ-828 Model Name Motor Single-phase induction motor Rated Voltage 230-240 V Fuse 250 V 5 A Rated Frequency 50 Hz Weight 6.5 kg External Width 252 mm...
Page 26
The future of your healthy kitchen. www.sanaproducts.eu 4DC010680_V.01...