1. Manuals
  2. Brands
  3. Infoblox Manuals
  4. Network Hardware
  5. Trinzic 100
  6. Installation manual

Infoblox Trinzic 100 Installation Manual

Appliance
Hide thumbs
Table of Contents

Advertisement

Quick Links

Infoblox Installation Guide for Trinzic 100 Appliance

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Trinzic 100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Infoblox Trinzic 100

Summary of Contents for Infoblox Trinzic 100

  • Page 1 Infoblox Installation Guide for Trinzic 100 Appliance...

  • Page 2: Table Of Contents

    1.1 Product Overview ................3 1.2 Trinzic 100 Hardware Components .

  • Page 3: Introduction

    The Trinzic 100 is a Class A digital appliance per FCC regulations, and it is RoHS and WEEE compliant. You configure and manage the Infoblox appliance through the Infoblox Grid Manager, a GUI that works seamlessly in Windows, Linux, and Mac environments using standard web browsers.
  • Page 4 Support. Trinzic 100 Appliance Rear Panel Figure 2 shows the rear panel components on the Trinzic 100. For explanations of the Ethernet port LEDs, and console and Ethernet port connector pin assignments, see Ethernet Port LEDs Interface Connector Pin Assignments...
  • Page 5 Reset Button WARNING: This button is intended for use by Infoblox technicians only. Ensure that you use this button with care if you want to reset the Trinzic 100 to its default factory settings As soon as you press the button, the Alarm LED is on. When you hold the button down for 5 seconds or more (but less than 15 seconds), the Alarm LED starts flashing slowly.
  • Page 6 RJ-45 rollover cable and two female RJ-45-to-female DB-9 adapters, or a female DB-9-to-female DB-9 null modem cable. The RJ-45 pin assignments follow IEEE 802.3 specifications. All Infoblox Ethernet ports are auto-sensing and automatically adjust to standard straight-through and cross-over ethernet cables.

  • Page 7: System, Environmental, And Power Specifications

    Output Power: 60 watts Installing the Trinzic 100 Appliance Follow the instructions to rack mount the Trinzic 100 appliance, connect it to a power source, and cable it to a network. Before proceeding, review Infoblox Safety Guide and follow the necessary precautions.
  • Page 8 5. Place the power adapter clamp on top of the power adapter, and then secure the clamp to the rack bracket by sliding the tabs on the clamp under the clips on the rack bracket, as shown in Figure 6 Figure 6 Securing the Clamp on the Power Adapter Copyright ©2018, Infoblox, Inc.All right reserved.

  • Page 9: Powering The Appliance

    Figure 8 Figure 8 Securing Rack Ears to the Rack Note: If you choose not to rack-mount the Trinzic 100 appliance, place the unit horizontally on a stable, cool flat surface, resting on all four rubber feet. Powering the Appliance...

  • Page 10: Accessing The Trinzic 100 Appliance

    Connecting to the Appliance Before you can access and configure the Trinzic 100 appliance through the Grid Master, you must be able to make a network connection to it. You must use the LAN1 port to connect to the appliance. The default network settings of the LAN1 port are 192.168.1.2/24 with a gateway at 192.168.1.1 (the MGMT port does not have default network settings).

  • Page 11: Infoblox Gui

    Otherwise, the DHCP server will assign a dynamic IP address to the appliance. Note that if you have already set the IP address for the appliance through the Infoblox CLI, GUI, or API, then auto-provisioning is disabled for the appliance and the lease address is not requested.

  • Page 12: Infoblox Cli

    Infoblox CLI The Infoblox CLI allows you to configure and monitor the appliance using a small set of Infoblox commands. You can access the Infoblox CLI through a direct console connection from your management system to the Infoblox appliance. (For more information, see Console Port .) You can...
  • Page 13 Rotates the specified log file, up to 10 previous. logfiles will be preserved The two main groups of Infoblox CLI commands are set and show To see the complete list of the set commands, enter help set after the command prompt. Likewise, to see a complete list of the show commands, enter help show. For information about the CLI commands, refer to Infoblox CLI Guide Copyright ©2018, Infoblox, Inc.All right reserved.

Table of Contents