Siemens SITRANS P Brochure & Specs page 42

SITRANS P measuring instruments for pressure
Transmitters for food, pharmaceuticals and biotechnology
SITRANS P300 for gage and absolute pressure
Selection and Ordering data
Further designs
Add "-Z" to Order No. and specify Order
code.
Sanitary process connection to
2
NEUMO Connect S flange connection
certified to 3A and EHEDG
• DN 50, PN 16
• DN 65, PN 10
• DN 80, PN 10
• DN 100, PN 10
• DN 2", PN 16
• DN 2½", PN 10
• DN 3", PN 10
• DN 4", PN 10
Aseptic threaded socket to DIN 11864-1
Form A
• DN 50, PN 25
• DN 65, PN 25
• DN 80, PN 25
• DN 100, PN 25
Aseptic flange with notch to DIN 11864-2
Form A
• DN 50, PN 16
• DN 65, PN 16
• DN 80, PN 16
• DN 100, PN 16
Aseptic flange with groove to DIN 11864-2
Form A
• DN 50, PN 16
• DN 65, PN 16
• DN 80, PN 16
• DN 100, PN 16
Aseptic clamp with groove to DIN 11864-3
Form A
• DN 50, PN 25
• DN 65, PN 25
• DN 80, PN 16
• DN 100, PN 16
1)
When the manufacture's certificate M (calibration certificate) has to be
ordered for transmitters with diaphragm seals, it is recommended only to
order this certificate exclusively with the diaphragm seals. The measuring
accuracy of the total combination is certified here.
2)
Whe the acceptance test certificate 3.1 for transmitters with direct-con-
nected diaphragm seals is ordered, this certificate must also be ordered
with the corresponding seals.
3)
Special Viton seal included in delivery.
4)
Lower measuring limit -100 mbar g (1.45 psi g).
5)
The weldable socket can be ordered under accessories
6)
Certified to 3A.
The maximum temperatures of the medium depend on the respective cell
fillings.
7)
3A certification only if used in conjunction with 3A-compliant sealing rings.
2/42 Siemens FI 01 · 2009
© Siemens AG 2008
Order code Selection and Ordering data
HART PA FF Additional data
Add "-Z" to Order No. and specify Order
code.
Measuring range to be set
Specify in plain text V (max. 5 digits):
Y01: ... up to ... mbar, bar, kPa, MPa, psi
9 9 9 9 9 9
Q63
Measuring point number (TAG No.)
9 9 9 9 9 9
Q64
Max. 16 characters, specify in plain text:
9 9 9 9 9 9
Q65
Y15: ...........................................
9 9 9 9 9 9
Q66
Measuring point text
9 9 9 9 9 9
Q72
Max. 27 characters, specify in plain text:
9 9 9 9 9 9
Q73
Y16: ...........................................
9 9 9 9 9 9
Q74
Entry of HART TAG
9 9 9 9 9 9
Q75
Max. 8 characters, specify in plain text:
Y17: ...........................................
Setting of pressure indication in pressure
9 9 9 9 9 9
N33
units
9 9 9 9 9 9
N34
Specify in plain text (standard setting: mA):
9 9 9 9 9 9
N35
Y21: mbar, bar, kPa, MPa, psi, ...
9 9 9 9 9 9
N36
Note:
The following pressure units can be selected:
bar, mbar, mm H
9 9 9 9 9 9
mmHG, inHG, psi, Pa, kPa, MPa, g/cm
N43
kg/cm
9 9 9 9 9 9
N44
*) ref. temperature 20 °C
9 9 9 9 9 9
N45
9 9 9 9 9 9
Setting of pressure indicator in
N46
non-pressure units
Specify in plain text:
Y22: ..... up to ..... l, m
9 9 9 9 9 9
N43 +
(specification of measuring range in pressure
P11
units "Y01" is essential, unit with max. 5 char-
9 9 9 9 9 9
N44 +
acters)
P11
Preset bus address
9 9 9 9 9 9
N45 +
possible between 1 ... 126)
P11
Specify in plain text:
9 9 9 9 9 9
N46 +
Y25: .....................
P11
Only "Y01" and "Y21" can be factory preset
9 9 = available
9 9 9 9 9 9
N53
Ordering example
9 9 9 9 9 9
N54
Item line:
9 9 9 9 9 9
N55
B line:
9 9 9 9 9 9
N56
C line:
C line:
*) *) *)
O , inH O , ftH O ,
2 2 2
2
,
2
, Torr, ATM or %
3
, m, USg, ...
7MF8023-1DB24-1AB7-Z
A02 + Y01 + Y21
Y01: 1 ... 10 bar (14.5 ... 145 psi)
Y21: bar (psi)
Order code
HART PA FF
9 9
Y01
9 9 9 9 9 9
Y15
9 9 9 9 9 9
Y16
9 9
Y17
9 9 9 9 9 9
Y21
9 9
Y22 +
Y01
9 9 9 9
Y25