Command access CL180 Installation Instructions

Installation Instructions

CL180
STEP 1: The door must be machined with a 3/8" wire raceway,
cylindrical lock pocket & prepped for a energy transfer
hinge. Make sure the cylindrical pocket is free of debris.
Cyl. Lock
Pocket
Cyl. Lock
Pocket
3/8 Wire Raceway
3/8 Wire Raceway
STEP 2: Run the wires from the ETH hinge through the 3/8"
raceway starting at the ETH hinge & exiting into the lock
pocket.
Cyl. Lock
Cyl. Lock
Pocket
Pocket
Cyl. Lock
Cyl. Lock
Pocket
Pocket
Cyl. Lock
Pocket
3/8 Wire Raceway
3/8 Wire Raceway
3/8 Wire Raceway
STEP 3: Screw the ETH hinge to the door. At this time DO NOT
connect the hinge wires on the jamb side to the wires
coming from the power supply.
EU: (Fail Secure) When power is applied, the outside trim will unlock. When
power is removed, the outside trim is locked.
EL: (Fail Safe) When power is applied, the outside trim will lock. When
power is removed, the outside trim is unlocked.
REX: (Request to Exit Switch) Monitors the inside handle.
EU (Fail Secure)
EU (Fail Secure)
EU (Fail Secure)
EU (Fail Secure)
EU (Fail Secure)
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
EL (Fail Safe)
EL (Fail Safe)
EL (Fail Safe)
EL (Fail Safe)
Bridge Rectifier
EL (Fail Safe)
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Command Access Technologies | 22901 La Palma Ave. Yorba Linda, CA 92831 | Phone: (888) 622-2377 | www.CommandAccess.com
Cyl. Lock
Pocket
ETH Hinge Pocket
Cyl. Lock
ETH Hinge Pocket
Pocket
ETH Hinge Pocket
ETH Hinge Pocket
3/8 Wire Raceway
Cyl. Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
3/8 Wire Raceway
3/8 Wire Raceway
Wire Transfer Hinge
3/8 Wire Raceway
Wire Transfer Hinge
Wire Transfer Hinge
Wire Transfer Hinge

LEGEND OF TERMS

Switch
EU (Fail Secure)
Wire Transfer Hinge
Switch
Wire Transfer Hinge
EU (Fail Secure)
Wire Transfer Hinge
Wire Transfer Hinge
EU (Fail Secure)
Wire Transfer Hinge
Switch
EL (Fail Safe)
Wire Transfer Hinge
Switch
Wire Transfer Hinge
EL (Fail Safe)
Wire Transfer Hinge
Wire Transfer Hinge
EL (Fail Safe)
Wire Transfer Hinge
STEP 4: Connect the wires exiting the lock pocket to the Bridge
Rectifier (included).
Bridge
Rectifier
Bridge
Rectifier
STEP 5: Connect the Bridge Rectifier to the plug exiting the
cylindrical chassis.
STEP 6: Carefully slip the connected cylindrical lock chassis into
the lock pocket paying close attention not to pinch any
wires.
Wire Transfer Hinge STEP 7: Mount the cylindrical lock per manufacturer's
instructions.
STEP 8: Connect the wires from the power supply at the ETH
hinge on the jamb side. Connect the hinge to the jamb.
12VAC/DC
12VAC/DC
or
or 12VAC/DC
12VAC/DC
Switch 24VAC/DC
or
24VAC/DC
EU (Fail Secure) or
Switch 24VAC/DC
24VAC/DC
EU (Fail Secure)
Power
12VAC/DC
Power
Supply
or
Power
Supply
Power
Switch 24VAC/DC
Supply
Supply
12VAC/DC
12VAC/DC
or
or 12VAC/DC
Power
12VAC/DC
Switch 24VAC/DC
or
24VAC/DC
EL (Fail Safe) Supply
or
Switch 24VAC/DC
24VAC/DC
EL (Fail Safe)
Power
12VAC/DC
Power
Supply
or
Power
Supply
Power
Switch 24VAC/DC
Supply
Supply
Power
Supply
Cyl. Lock
Cyl. Lock
Bridge Pocket
Pocket
Rectifier Cyl. Lock
Cyl. Lock
Bridge
Pocket
Pocket
Rectifier
Cyl. Lock
Bridge
Pocket
Rectifier
Cyl. Lock
Pocket
Cyl. Lock
Bridge
Bridge
Pocket
Rectifier
Bridge
Rectifier
Bridge
Rectifier
Rectifier
Bridge
Rectifier
Plug
Plug
Plug
Plug
Plug

ELECTRICAL SPECIFICATIONS

SOLENOIDS:
CURRENT
VOLTS
150mA
24VAC/DC
250mA
12VAC/DC
SWITCHES: .25A 24VAC/DC
REX:
Green - Common (C)
Blue - Normally Open (NO)
Grey - Normally Closed (NC)
SEE BACK FOR REX TEMPLATE
Cyl. Lock
Pocket
Cyl. Lock
Pocket
Cyl. Lock
Pocket
COIL RESISTANCE
159 Ohms +/- 10%
49 Ohms +/- 10%
#20223_B