Advertisement
PARAMETER
WDBL1014V/WDBL1014VS/
Model No/Item No
WDBL1014VT/WDBL1014VB
Washing/drying Capacity
10.0/7.0kg
Max.spin speed
1400rpm
74kg
Net Weight
Dimension(WXDXH)
595X660X845mm
Rated Voltage
220 -240V
Heating Power
1900W
Washing Power
100W
Drying Power
1700W
Spinning Power
500W
Add Detergent, Close the Door and Set the Program
Load the clothes to be washed in the drum and close the door.
Add the detergent into the relevant compartments for the type
of program you are going to select, Add detergent as described
in Detergent and Additives section of User's Operation
Manual.
1.Press the "On/Off" button.
2.Spin program selection button to required program, start up and
default the program as "Cotton".
3.Select washing temperature, spin speed and times of extra rinse
by pressing "Temp", "Spin" and " Rinse" buttons.
4.Press "Options" button to select additional functions.
5.After starting the program, display window displays program
length (hours: minutes), times of rinse, washing temperature
and additional function options in sequence. eight of clothes.
Addition function selection
At standby state, press "Options" button to select additional
function for current program. Select only one function for each
press, and then corresponding icon flashes. After starting up,
program cannot be changed.
Pre-wash
·Select the function to conduct pre-wash so as to enhance washing
effects and better remove stains. This function is suitable for
heavy dirt clothes.
·Before inflowing, laundry detergent/ washing powder can be
added to pre-wash box, and washing powder must be added to
main wash box.
Intensive
·The function can be selected to prolong washing time, strengthen
washing effects and better remove stain.
Rinse
•
After setting the Rinse function, add a rinse process for one time
before operating the softening program, so the total operating time
correspondingly increases.
•This function is selected in standby state and cannot be changed
after starting.
•After selecting the program, the default rinse times (including
softening) will light up. Each time the Rinse key is pressed, one
time rinse will be added to the default rinse times, increasing to
5 times at most.
Inlet water warning
If tap is not opened, or water pressure is over low, inlet water
fault icon will display, and display screen will prompt "F01" to
give alarm.
Drainage warning
If the pipe is squeezed, drainage will not be smooth. In case of
failing to completely drain for long time, drainage fault icon will
display, and display screen will prompt "F03" to give alarm.
Door Lock Icon
After the program starts the Door Lock icon will light up and
the door will be locked.
·After completing program, door lock unlocks automatically.
During pause, if door opening condition can be met halfway,
the door lock will unlock and its indicator light will go out.
·When door lock indicator light flashes, door shall not be opened
forcibly so as to avoid personal injury.
Delay End Function
Delay End function allows to run the machine at the consumers'
convenience, for example, at night when electricity is cheaper.
•Only under the standby mode, this button is valid for
selecting the reservation time.
•After the reservation function is selected, the time will
increase 1h when each time the reservation button is pressed.
Before reservation, if the program time does not satisfy the
integral multiple of 1h, it shall be completed by pressing the
reservation key for the first time, and then the time increases
1h when each time the reservation button is pressed. If the
reservation is selected, before the program runs, the current
reservation can be canceled by turning the button to select
other programs.
•The delay time must be longer than the wash program length
as the delay time is the time program will finish. For example:
if the selected program time is 02:28, the delay time selected
must be between 03:00 and 24:00.
•When the reservation process is operated, the icon of
'reservation time' will be on. When the reservation process
is finished, the icon of 'reservation time' will be off, while
the icon of the 'remaining time' will be on.
•
If delay end is selected and start button is not pressed, delay can
be canceled by rotating rotary knob before starting.
•To cancel the delay time during the delay program, you need
turn the machine off by pressing "On/Off" button for 2 seconds.
Mute Function
When the machine is in the state of holding, pause or operation,
press "Rinse+ Spin" buttons for 2 seconds, The display will
show "bEEp oFF" . All the buzzing will be turned off except
the alarms.
When the machine is in the mute state, press "Rinse + Spin"
buttons for 2 seconds until "bEEp on" appears. All the
buzzing will be activated.
Child Lock
To strengthen the safety of children, this machine is equipped
with Child Lock function.
When the programme starts, press "Temp. +Rinse"
button for 2 seconds. The display will show "SAFE on", and
then Child Lock is set up. Repeat the same operation, the
Child Lock will be released when "SAFE oFF" appears.
•When the Child Lock is set, all function buttons will be
shielded.
•When you turn the machine off by pressing the "On/Off"
button, child lock is released.
•
After completing program, child lock will automatically
unlock.
To Start the Program
After you have selected your options and placed detergent
withinthe detergent dispenser, turn on the water tap and press
the "Start / Pause" button. The screen will display the current
program progression with icons from left to right. It also
displays the remaining program time.
To Cancel the Program or Reselect the Options
1.Press the "On/Off" button for 2 seconds to turn off the
machine.
2.Press "On/Off" button to turn on the machine. Select the
new program and options.
3.Press "Start / Pause"to start the new program without adding
any extra detergent.
End of the Program
When programme finished its running, it will display "End".
If no operation is taken in 2 minutes, the machine will turn
off automatically.
1.Press "On/Off" button for 2 seconds to turn off the machine;
2.Close the tap;
3.Open the door and take the washed clothes out;
4.Slightly open the door to remove moisture in the pump.
Reload in Process
If you want to reload clothes in the process of washing, please
press "Start/Pause" button.
•If reload icon
light up, the door can be opened in the
process, remaining time and the Door Lock icon in display
will flash. Then the Door Lock icon will go out, and the door
can be opened.
•If reload icon
doesn't light up, the Door Lock icon
doesn't flash, it indicates that current temperature is over 50℃
or you have passed the time for reloading in the process,
namely no clothes allowed to load into the machine.
Automatic weighting
Washing machine displays "----" after startup, indicating
that it is weighing automatically. It will adjust program
length (hours: minutes) automatically according to weight of
clothes.
Dry
Press the "Dry Level" button to select the dry time and additional
functions of dry. When the Iron
, Cupboard
and Extra
Dry
functions are selected, the corresponding icon will
light up, and the remaining time of the program will be
displayed on the display window. When the [Time Dry]
function is selected, the icon of Time Dry
will light up.
The washing machine can sense the weight of clothes to
adjust the dry time automatically.
Before drying, please confirm whether the clothes can
·
be dried (please refer to the program table to confirm
the type of clothes that can be dried).
Before starting to dry, make sure that the tap is open and the
·
cold water is in place.
Before separately drying, please take the dehydrated clothes out
·
from the drum, and put it into the drum after making it loose.
When little clothes or light clothes are dried, for which, the
·
dry time may be shorter than the setting time.
·
If the hand-washing clothes requires for drying, before drying,
please select the spin with high speed as possible according to
the clothes types. It is recommended to select the "Spin
+ Dry Level" program.
At the end of dry, the washing machine will run for a period
·
of time according to a certain rhythm to loosen the clothes
and reduce the wrinkle.
The wall attachment of excessive and dehydrated cotton
·
clothes may affect the dry effect. So it is recommended to
dry the clothes after loosening it manually.
·
The overload dry may affect the dry effect, while the excessive
dry may cause the wrinkles of clothes. For the chemical fiber
clothes, such as the shirts, etc., the iron mode shall be selected.
·
If the clothes with different materials are dried together, the
dry effect may be affected. So it is recommended to classify
the clothes before drying.
If the dry failure occurs, please refer to the contents of [Dry
·
Fault] for processing.
[Iron]
function owns the effect that the clothes with little
water can be ironed after being dried.
[Cupboard]
function owns the effect that the clothes
can be worn instantly after being dried.
[Extra Dry]
function owns the effect that the clothes can be
stored up after being dried.
[Time Dry]
function refers to dry the clothes for a
specified time.
Users press the "Dry Level" button to select any type of dry time
with 6 types, including 30 minutes, 1 hour, 1.5 hours, 2 hours, 3
hours, and 4 hours. Please select a reasonable dry time.
Otherwise, the clothes will not be dried fully if the dry time is
too short.
Note:
The wet clothes still dripping are not suitable for drying,
which may cause the machine to alarm!
2
Advertisement
