Table of Contents
Advertisement
(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold
separately) to the projector. (See page
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projec-
tor processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digit
Response code format
Normal response
O
K
Info
When more than one code is being sent, send each command only after the response code for the previous command from
the projector is verified.
To conserve power in STANDBY mode, the CPU in this model will enter Deep Sleep mode approximately 10 seconds after the
last command is received. In the case of transmitting commands during Deep Sleep mode, it takes a maximum of 30 seconds
until the response code is received. If subsequent commands are sent to the projector within 10 seconds, the projector will
reply immediately. If no further commands are received within 10 seconds, the projector will again return to Deep Sleep mode.
Please note that Deep Sleep mode is only activated in STANDBY mode. There is no delayed RS-232C response when the
projector is in operation.
Special commands, "POWR????" and "TLPS_ _ _1" are available for applications that require continuous polling. These
commands will not wake the CPU in Deep Sleep mode and the projector will provide immediate reply in STANDBY mode. "1"
will indicate Power on, "0" will indicate STANDBY mode. When the power is turned on during standby with the "POWER ON"
command, wait for at least 40 seconds after the power has been turned on, and then transmit the next command.
We suggest disabling the AUTO SEARCH feature before initiating RS-232C communications. If AUTO SEARCH is enabled, it will
be necessary to send the STANDBY mode command "POWR_ _ _0" two times to power down the projector. (The first "POWR_ _
_0" command cancels AUTO SEARCH and the second "POWR_ _ _0" command will put the projector into the standby mode.)
Note
Do not repeatedly or periodically send any commands other than "POWR????" and "TLPS_ _ _1" in STANDBY mode as
it will cause problems.
When the projector is put into the standby mode, a message "Shutting Down. Please Wait." is displayed for about 20 seconds.
At that time, if the "POWR_ _ _1" command is being sent, "ERR" will be returned and this command is not received.
When using the computer control function of the projector, the adjustment values cannot be read by the computer.
Therefore, confirm the values by transmitting the display commands (e.g. "RARE_ _ _0") for each adjustment menu and
checking the values with the on-screen display. If the projector receives adjustment/setting commands other than menu
display commands, it will execute the commands without displaying the on-screen display.
Commands
Example:
When "BRIGHT" of INPUT 1 image adjustment is set to –10.
Computer
_
R
A
B
R
CONTROL CONTENTS
POWER ON
STANDBY
POWER STATUS
LAMP POWER STATUS
VOLUME (0 - 60)
MUTE ON
MUTE OFF
KEYSTONE (–127 - +127)
DIGITAL SHIFT (–96 - +96)
22
for connection.)
Parameter 4-digit
0DH
Return code (
)
–
1
0
COMMAND PARAMETER
RETURN
P
O
W
R
_
_
_
1
OK OR ERR
P
O
W
R
_
_
_
0
OK OR ERR
P
O
W
R
?
?
?
?
0:OFF, 1:ON
0:OFF, 1:ON, 2:COOLING
T
P
O
W
_
_
_
1
3:SHUTTING DOWN
V
O
L
A
_
_
*
*
OK OR ERR
M
U
T
E
_
_
_
1
OK OR ERR
M
U
T
E
_
_
_
0
OK OR ERR
K
E
Y
S
*
*
*
*
OK OR ERR
L
N
D
S
_
*
*
*
OK OR ERR
Parity bit: None
Stop bit: 1 bit
Flow control: None
Return code (
Problem response (communication error or incorrect command)
E
R
R
Projector
O
K
CONTROL CONTENTS
BLACK SCREEN ON
BLACK SCREEN OFF
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT CHECK
FREEZE ON
FREEZE OFF
AUTO SYNC START
0DH
)
0DH
Return code (
)
COMMAND PARAMETER
RETURN
I
M
B
K
_
_
_
1
OK OR ERR
I
M
B
K
_
_
_
0
OK OR ERR
I
R
G
B
_
_
_
1
OK OR ERR
I
R
G
B
_
_
_
2
OK OR ERR
I
V
E
D
_
_
_
1
OK OR ERR
I
V
E
D
_
_
_
2
OK OR ERR
I
C
H
K
_
_
_
0
OK OR ERR
F
R
E
Z
_
_
_
1
OK OR ERR
F
R
E
Z
_
_
_
0
OK OR ERR
A
D
J
S
_
_
_
1
OK OR ERR
-89
Advertisement
Table of Contents
