Boil Mode - Zojirushi CV-TYQ40 Operating Instructions Manual

CV-TYQ_0607_E_20180329

BOIL MODE

1
Open the Upper Lid and fill
the Inner Container with water
using a pitcher or other ontainer.
To monitor the amount of water
水量ボールの位置で水量が
you are filling, look at the Water
ひと目で分かります。
Level Ball position.
Water
Level
Present Water
Gauge
Level
Water Level Ball
The Water Level Ball is not
seen when the water level
is higher than the scale of
Water Level Gauge.
2
Close the Upper Lid and connect the Power Cord.
Close the Upper Lid
securely.
To ensure safe
operation while
boiling and to prevent
scalds if the product
is overturned.
2
NOTE
1
Do not allow the
●
Be sure to insert the end of the
Appliance Plug to
Power Cord securely.
get soiled with dust
Otherwise, may cause electric
or come into contact
shock, short circuit, smoke or with metal objects
fire. such as pins.
6
NOTE
Do not fill the
●
Inner Container
directly from a
water faucet or
place the product
on a wet surface
such as a sink. (Exposing
the heating element directly
to water may cause
malfunction.)
Avoid splashing water on
●
the Body or Control Panel.
(May cause malfunction.)
Before use,
●
check the Inner
Maximum Water
Lid Gasket for
Level Line
any deformation.
(May cause
steam leakage.)
It automatically starts the boiling
process.
The BOIL light turns on and the
Display shows the water
｡
temperature in 5 C increments.
Turns on
Beep
How to set the Keep Warm mode:
●
see P.10-11
How to set the Quick Temp mode:
●
see pg. 12
At your initial use or when
●
using the product after a long period of storage:
Do not fill over the Maximum
●
Water Level Line. (Hot water may
Fill the Inner Container with water to the Maximum Water
overflow from the Steam Vent.)
Do not fill the Inner Container with Level Line (
●
hot water. (The Automatic
reaches a boil, press the UNLOCK button, then press the
Shut-Off function may be
DISPENSE button to dispense about 1 liter of hot water in
activated.) (see P.9)
order to rinse the water route, and dispose the remaining
Do not fill the Inner Container with
●
water. Fill with fresh water.
any liquid other than water.
Do not use water additives such
●
as charcoal for water purification When using mineral or Alkalized Ionic water:
●
or mineral additives. (Small
When mineral or Alkalized Ionic water is used, a floating
particles may get clogged inside
of the product.) residue may develop or a milky white substance may form
on the surface of the Inner Container. This is due to the
If you wish to shorten the
●
completion time, add less water to ingredients in the water and is harmless to your health.
the Inner Container.
Frequent cleaning is recommended.
When boiling has completed, a melody
sounds and it automatically switches
to 90 ｡ C Keep Warm mode.
The BOIL light turns off, the KEEP WARM
light turns on and "100" appears on the
Display.
temperature drops to about
90 ｡ C, "90" appears on the
Turns off
Turns on
Length of time until the water
Time required to boil water:
temperature reaches about 90
Approx. 1 hour and 10
Approx. 37 minutes
※
minutes
｡
(At a room temperature of 23 C with the
(At a room temperature of 23 ｡ C with the
Inner Container filled to the Maximum
Inner Container filled to the Maximum
Water Level Line with water temperature
at 23 ｡ C.)
Water Level Line.)
The length of time for the water
Includes approx. 4 minutes to
●
※
temperature to reach 90
Dechlorinate.
depending on the temperature of the
room and water.
The first time
you use the product you
may notice the smell of
plastic. This is normal
and will gradually fade
away.
), and boil water as directed. Once it
(Always remember to attach the Filter.)
How to change the Information Sound
from a melody to a beep. (see pg.14)
How to set the Keep Warm mode:
98 ｡ C Keep Warm Mode. (see pg.10)
80 ｡ C Keep Warm Mode. (see pg.10)
70 ｡ C Keep Warm Mode. (see pg.11)
Vacuum Insulation (Non-Electric)
When the water
Keep Warm Mode. (see pg.11)
Display.
NOTE
Add water when the water level is
●
low during the Keep Warm mode.
(The product automatically begins
heating the water.) If the water level
is still not high enough, it will not
automatically switch to Boil. In this
case, press the REBOIL/QUICK
TEMP button to manually start the
process. (see pg.9)
｡
C:
Please follow the instructions below
●
to prevent the risk of scalding:
・Do not cover the Steam Vent with a
cloth.
・Do not touch the Steam Vent or
bring your hands or face near the
Steam Vent.
・Do not open the Upper Lid while
the BOIL light is on.
・Do not dispense hot water while it
｡
C will vary
is boiling.
7