Table of Contents
Advertisement
Quick Links
Operating Instructions
Series L 70000 Spring Driven Cord Reels
Model Numbers:
L 70075 123 3
L 70100 123 7
L 70100 123 3
L 70075 123 7A
L 70075 123 3A
L 70100 123 7A
L 70100 123 3A
L 70075 123 9
L 70075 123 3B
L 70100 123 9
L 70100 123 3B
L 70075 123 9G
L 70075 123 7
L 70100 123 9G
Dimensions
SAFETY
Personal injury and/or equipment damage may result if proper safety
precautions are not observed.
• Ensure that only a qualified electrician installs/services this
equipment.
•
• Ensure that power supply voltage does not exceed maximum
voltage rating of reel.
•
• Ensure that all electrical power is removed from reel before
servicing.
•
• A high-tension spring assembly is contained within the reel.
Exercise extreme caution.
•
• Check for frayed and/or broken wires before each use. Pull
electrical cord from reel by grasping the electrical cord itself,
not the work device.
•
• If an electrical malfunction should occur, remove power from
reel immediately.
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
L 70075 123 X
L 70075
L 70100 123 X
L 70100
L 70100 124 X
L 70100 124
A
20 1/4"
B
19 3/4"
C
7 7/8"
D
3 7/8"
E
12 1/2"
• Ensure that reel, electrical cord, and equipment being serviced
•
• If reel ceases to unwind or rewind, remove power immediately.
•
• Treat and respect the reel as any other piece of machinery,
•
• All cord reels with flying leads must be hard wired into the
•
WARNING: Even low voltage can cause irreparable damage or
death! Exercise extreme caution while operating or servicing this
equipment.
IMPORTANT
Read this manual carefully before installing,
operating or servicing this equipment.
are properly grounded. Use an ohmmeter to check ground
continuity.
Do not pull or jerk on electrical cord!
observing all common safety practices.
electrical circuit to ensure proper function.
Form# 1287-916 Rev: 4/2017
Advertisement
Table of Contents
Related Manuals for ReelCraft L 70100 123 7
Summary of Contents for ReelCraft L 70100 123 7
- Page 1 • If an electrical malfunction should occur, remove power from reel immediately. Form# 1287-916 Rev: 4/2017 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
- Page 2 Then take the cable clamp and screw it down to the right- most screw on the brush assembly (with the brush assembly fac- ing upward). 10. Replace cover (2). 11. Replace latch and wind cable onto reel. 12. Install bumper stop (10). Page 2 www.reelcraft.com...
- Page 3 All cord reels with GFCI receptacles must be hard wired into the electri- alignment by loosening nuts (13) and sliding finger assembly cal circuits. Use of 2 or 3 prong plugs may cause a potential (14). malfunction of the GFCI receptacle. www.reelcraft.com Page 3...
- Page 4 Refer all other repairs, other than those listed, only to an authorized assembly. service person or directly to Reelcraft. Failure to do so can result in Remove zip tie (not pictured), being careful to not damage wires. personal injury and/or equipment damage and may void the warranty.
- Page 5 Figure B www.reelcraft.com Page 5...
- Page 6 262938 262938 262938 262938 Voltage AMPS Item # Description # Req'd L 70100 123 3B L 70075 123 7 L 70100 123 7 L 70075 123 7A L 70100 123 7A Snap Ring 300007 300007 300007 300007 300007 Lock Nut...
- Page 7 602696-1-35 602696-1-35 602696-1-35 602696-2-35 602696-2-35 Split Lock Washer 902016 902016 902016 902016 902016 Adapter Plate 261577 261577 261577 261577 261577 Spacing Washer 262422 262422 262422 262422 262422 Collector Ring Cover 262938 262938 262938 262938 262938 Voltage AMPS www.reelcraft.com Page 7...
Need help?
Do you have a question about the L 70100 123 7 and is the answer not in the manual?
Questions and answers