Jump-Starting Your Vehicle; Negative Grounded Battery - Motomaster Eliminator 11-1913-6 Owner's Manual

16
COMMON ACTIONS AND UNIT RESPONSES (cont'd)
The following actions turn the unit on and activate
the LCD screen:
... the backlit LCD screen will display the Battery Status Icon, Battery Voltage
If the clamp connections
Indicator, and the Clamp Icons. The Alarm Icon, the "+" and "–" signs and the
to the battery's positive
and negative terminals Reverse Polarity Icons will flash and the unit will sound a warning continuously
are reversed (refer to until the clamps are disconnected from the battery.
the "Jump-Starting Your
Vehicle" section) ...
... the backlit LCD screen will display the Battery Status Icon and Battery
If the red and black
Voltage Indicator. The Clamp Icons, "+" and "–" signs and the Alarm Icon
clamps touch each other
(refer to the "Jump-Starting will flash. The unit will sound a two-second warning every ten seconds
Your Vehicle" section) ... continuously until the clamps are separated.
When the unit is ... a beep will sound and the backlight will turn on for 10 seconds only. The
LCD screen will continue to display the Battery Status Icon and Battery Voltage
charging or recharging
Indicator. The bars on the Battery Status Icon will change from empty to solid
using the built-in 120
Volt AC Charger (refer to (bottom to top) repeatedly.
the "Preparing For Use"
section) ...
Viewing Battery Status
The Battery Status Icon and Battery Voltage Indicator indicate the battery
charge level as follows:
•
If the battery charge level is at full capacity, four solid bars will display.
•
If the battery is partially charged, two or three solid bars will display.
•
If the battery is nearly empty, one solid bar will display. The unit should be
charged at this time.
•
If the battery is completely empty, four blank bars will display. The unit
MUST be charged at this time or the unit's built-in low voltage protection
will activate. The empty Battery Status Icon will flash for a short period
of time before automatic shut down. The unit will not operate until the
battery is recharged.
J7C09ME_11-1913_EN_082418.indd 16-17

JUMP-STARTING YOUR VEHICLE

Negative Grounded Battery

OFF ARRÊT
ON
MARCHE AIR 3.1A USB
JUMPER / DÉMARREUR
® ®
MD MD
Œ 
Turn off vehicle ignition and all
accessories (radio, A/C, lights,
connected cell phone chargers,
etc.), put vehicle in "park" and
set emergency brake.

Make sure the Jump-Starter
Power Switch is turned to OFF.
IMPORTANT – To reduce the risk of
a spark near battery:

•
Stay clear of fan blades, pulleys,
and other parts that can cause
injury.
•
Check polarity of battery posts.
A positive (POS, P, +) battery post
usually has a larger diameter than
a negative (NEG, N, –) battery
post.
•
Remove jumper clamps from
clamp tabs.
NEVER allow the DC
output clamps to touch
each other. This may
cause a spark.
‘
Ž
Connect the positive (red)
clamp from battery booster to a
positive (POS, P, +) ungrounded
post of the battery.
17
4
3
– +
–
+ + +
Connect the negative (black)
clamp from the battery booster
to vehicle chassis (must be a
heavy gauge metal part
of the frame) or engine
block away from the battery.
DO NOT connect the clamp to
carburetor, fuel lines, or sheet
metal body parts.
When the clamps are
connected properly, the backlit
LCD screen will display the
following to indicate the unit is
ready to jump-start:
The Battery Status icon, Battery
Voltage Indicator, Clamp Icons
and the "+" and"–" signs light
solid. The jump starter icon will
flash to indicate the clamps are
properly connected.
Turn the Jump-Starter Power
Switch on.
8/24/2018 11:15:45 AM