Advertisement
Available languages
Available languages
• Turn off all noise sources – radios, compressors, generators,
heavy equipment, etc.
• Know how to cancel an alarm or turn off the system before
activating.
• If a false alarm is tripped notify customer service immediately.
• Test the system on a monthly basis to ensure proper functioning
• Check cellular signal, power supply, and that sensors are secured
on a daily basis.
Recommended Locations
Recommended for use in enclosed areas, offices, climate controlled
storage, and monitoring interior spaces.
• The DS210 functions best when areas being protected are
bounded by solid barriers. Walls and floors provide good back-
drops for detecting moving heat (infrared) sources.
• For best detection, locate the motion sensor so that intruders
move across detection zone patterns, rather than toward or away
from the sensor (Fig. 2).
• Check areas for potential sources of false alarms. Remember
that the sensor responds to quick changes in heat patterns within
its coverage pattern. Avoid placing in direct or reflected sunlight,
or near objects that can be heated quickly by sunlight. Do not
place the DS210 looking at windows. Don't place it near heating
or cooling sources, like heater ducts or air conditioners, which
might direct hot or cold air onto the sensor. Avoid appliances such
as space heaters which can rapidly heat up.
• Take into consideration the normal use of the area. Are there bats,
mice or other animals that could activate the sensor?
• Do not obstruct the coverage pattern with furniture or other
equipment.
Installing & Changing Battery
This wireless sensor requires a non-rechargeable CR-123 3.0 Volt
Lithium battery.
CAUTION:
POTENTIAL
FAILURE. Do not touch the electronic components inside the device,
except the reset button and battery.
TO INSTALL BATTERY
1. Using a flat screwdriver, open the housing. Insert the screwdriver
about .25" (6mm) at the tab on the bottom of the unit (Fig. 3). The
screwdriver will enter the slot at about a 45˚ angle. Pry downward
on the handle of the screwdriver until the latch holding the cover
to the housing base releases.
2. Install the battery using the polarity (+ and -) markings on the
battery and equipment. Do not use excessive force. If the battery
does not fit, ensure that it matches the polarity markings (Fig. 1).
3. Press the Reset Button (C) on the device. After resetting the
sensor (see Device Registration), replace the cover. By open-
ing the device, the Base Unit may display a tamper fault.
TO CLEAR A FAULT
a. Select Display.
b. Scroll list of fault(s).
c. Select Clear.
d. Enter master code.
e. Select OK.
TO CHANGE THE BATTERY
CAUTION: Never use a damaged or worn out battery.
1. Carefully remove the old, discharged battery. Dispose of the bat-
tery according to local regulations.
2. Install new battery using the polarity (+ and -) markings on the bat-
tery and equipment. Do not use excessive force. If the battery
does not fit, ensure that it matches the polarity markings (Fig. 1).
3. Press the Reset Button (C) on the device to re-register the sen-
sor and restore programming. After resetting the sensor, replace
the cover. By opening the device, the Base Unit may display a
tamper fault.
TO CLEAR A FAULT
a. Select Display.
b. Scroll list of fault(s).
c. Select Clear.
d. Enter master code.
e. Select OK.
EQUIPMENT
MALFUNCTION
Device Registration
To activate the device, it must first be assigned to your DS100 Base
Unit. Refer to the DS100 JobSite Security Portable Alarm System
Instruction Manual for more details on registering a device during the
initial setup.
NOTE: The system must be disarmed prior to any programming
changes.
1. Press the MAIN MENU button on the keypad of the DS100 Base
Unit.
2. Using the keypad, enter the master code.
3. Use the up and down arrows to scroll through the menu until the
System Settings menu is displayed. Select OK.
4. Use the up and down arrows to scroll through the menu until the
Wireless Device Maintenance menu is displayed. Select OK.
5. Use the up and down arrows to scroll through the menu until the
Add/Replace Device screen is displayed. Select OK.
6. The next available device number will be displayed. Up to 48 sen-
sors can be registered to the system. If there are no slots avail-
able, the screen will display ALL DEVICES IN USE. When the
device number is shown, select OK.
7. Using a flat screwdriver, open the housing. Insert the screwdriver
about .25" (6 mm) at the tab on the top of the unit. Pry downward
on the handle of the screwdriver until the latch holding the cover
to the housing base releases (Fig. 3).
8. When prompted by the LCD screen to RESET DEVICE, press and
release the reset button (C) located on the control board. The
screen will indicate that the device has been registered.
9. Snap the cover in place.
10. To edit the description of the device, select EDIT.
11. To edit the description, use the keypad to type a description of up
to 8 characters. The character that is being changed will be under-
lined. To move back a character, use the left/down arrow. To move
forward a character, use the right/up arrow. When complete, select
OR
SAVE.
IMPORTANT: Write the device description and corresponding
device number on the Sensor Location List included with the
DS100 JobSite Security Portable Alarm System. Keep this sheet
for reference. This information will be needed during the monitoring
service enrollment process. As device changes are made, be sure
to contact D
WALT customer service to make adjustments to the
E
monitoring service.
12. After registration, test the sensor. If programming through the initial
setup, the test function will be included in the setup sequence. If
adding the Indoor Motion Sensor after the alarm system has been
programmed, use the TEST button on the keypad.
Tests
WALK TEST
Wait 90 seconds since last motion was detected then walk through the
areas where protection is expected. When motion is detected, it will
unsecure and be removed from the test list on the Base Unit LCD
screen. Determine the limits of the coverage by repeating this test until
the motion is not detected.
COVERAGE TEST
While the system is unarmed, performing this test will indicate the
coverage area without sending an alarm. With the cover on the sensor,
hold a magnet on the bottom left side of the sensor until a red LED is
shown in the window. This activates the 1 minute test mode. Within
this period, a red LED will light every time the unit senses motion.
Mounting
• There are several options for mounting the DS210. The Indoor
Motion Sensor has two mounting holes on the back of the sensor
for easy installation using two #6 screws (provided) or two
#8 screws (not provided). Mounting tape and a hook and loop
fastener are also included. For mounting tape or hook and loop
fastener placement, see Figure 4.
• Mount the sensor 3–6' (.9–1.8m) from the floor. Any height outside
of this range will decrease the sensitivity of the motion detector.
• To eliminate false alarms, be sure that the sensor is secure so
it will not be bumped or otherwise moved.
2
Advertisement
