1. Manuals
  2. Brands
  3. SRS Labs Manuals
  4. Controller
  5. RMC12, RMC8
  6. Instruction manual

SRS Labs RMC12, RMC8 Instruction Manual

Rack hoist controller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Rack Hoist Controller
Instruction Manual
Models:
RMC12, RMC8
version 02.01 since 1 June 2017
ATTENTION!
This instruction manual contains important information about the installation and the use of
the equipment. Please read and follow these instructions carefully.
Always ensure that the power to the equipment is disconnected before opening the
equipment or commencing any maintenance work.
RMCXX_en_manual_M175
( 1 / 16)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RMC12, RMC8 and is the answer not in the manual?

Questions and answers

Related Manuals for SRS Labs RMC12, RMC8

Summary of Contents for SRS Labs RMC12, RMC8

  • Page 1 Rack Hoist Controller Instruction Manual Models: RMC12, RMC8 version 02.01 since 1 June 2017 ATTENTION! This instruction manual contains important information about the installation and the use of the equipment. Please read and follow these instructions carefully. Always ensure that the power to the equipment is disconnected before opening the equipment or commencing any maintenance work.

  • Page 2: Important Instructions

    Safety information IMPORTANT INSTRUCTIONS All safety and operating instructions should be read before the equipment is installed or operated. IMPORTANT SAFETY INFORMATION The following general safety precautions have to be observed during all phases of operation, service, and the repair of this equipment. Failure to comply with these precautions or with specific warnings in this manual violates safety standards of design, manufacture, and the intended use of this equipment.

  • Page 3: Functions And Control

    Functions and Control RMC hoist controller was designed to control up to 12 (RMC-12) electrically compatible motors either separately or simultaneously; via DIGITAL cable remote or locally on the RMCseries base unit. All electrical components carry their own individual CE certification and comply with European Directives.

  • Page 4: Rmcseries Base Unit

    RMCseries base unit RMCseries front panel RMCseries rear panel E-stop connector NC4FDL • Remote A / Remote B link connectors are 3-pin /NC3MDL+NC3FDL/ or NC3MAH and NC3FAH • When controllers are linked via LINK, the STOP and GO signals of all controllers in LOCAL •...

  • Page 5: Optional Cmc-Digital Remote

    Optional CMC-DIGITAL remote CMC-DIGITAL allows controlling of the RMCseries via the DIGITAL wired remote STOP: This latching pushbutton switch turns the Hoist Control system off. Once the STOP button has been pressed, it is locked into the off position and must be rotated clockwise to be released. This pushbutton switch turns the selected channels of Hoist Control system on when they are active.

  • Page 6: Direction Switch Led

    DIRECTION SWITCH LED Green • DOWN • No light stays in position • STATUS LED: Green Device ready for action • Indicates that GO button is active • Orange Indicates the activity of direction switch; LED blinks with the movement •...

  • Page 7: E-Stop Connector

    Output wiring Remote multipin connector Amphenol DS3106A28-21P Function CMC12A CMC8A M1 down M1 up M2 down M2 up M3 down M3 up M4 down M4 up M5 down M5 up M6 down M6 up M7 down M7 up M8 down M8 up M9 down M9 up...

  • Page 8: Remote1/Remote2 Connector Or Link Connectors

    Remote1/Remote2 connector or LINK connectors LINK connectors are used for linking of two or more RMC units together in case that linked operation of units is required. For link unit need be in the local mode. E-STOP and GO signal is sent via network to all linked controllers.

  • Page 9: Linking Of Rmcseries Units

    Linking of RMCseries units Up to 10 RMC base units can be linked together for a group operation of GO buttons. For linking of RMC base, use a 3-pin XLR cable connected as 1:1 between pins 1-3. Data are transferred thru the RS485 line. All connected devices will have GO/E-STOP button linked in the LOCAL mode.

  • Page 10: Technical Data

    Technical data Main Power: AC208-230V, 50/60Hz, T2.5 • *Optional : AC110V / 60Hz • Protections and Safety: Dry contacts – all outputs are galvanic isolated • Double - Recessed Emergency stop + SIL3 safety module • Double encoded data communication •...

  • Page 11: Warranty

    Warranty RMCseries hoist controller is covered by a 2-year manufacturer’s warranty. For extended warranty conditions please contact the manufacturer at sales@srs-group.com. Warranty covers the original factory installed components of the controller and their correct functioning. Warranty voids if any part or replacement components are installed or modified without authorization from the manufacturer and/or the internal circuit is tampered or modified and/or the controller is operated outside normal use conditions –...

  • Page 12: Declaration Of Conformity

    Declaration of conformity DECLARATION OF CONFORMITY According to guidelines 89/336 EEC and 92/31 EEC, 90/337 CEE Annex II A: Name of producer: SRS Group s.r.o. Address of producer: Rybnicna 36/D, SK- 83106 Bratislava, Slovak Republic www.srs-group.com/ sales@srs-group.com, +421244681417 Declares that the product Name of product: RMCseries hoist controller: RMC8, RMC12 and variants Types...
  • Page 13 ( 13 / 16)
  • Page 14 ( 14 / 16)
  • Page 15 ( 15 / 16)
  • Page 16 Copyright 2017 SRS Group, s.r.o. | Specifications subject to change without notice. Document: RMCXX_en_manual_M175 | Version 02.01 | Actual as of: 1 June 2017 SRS Group s.r.o. Rybnicna 36/D | 831 07 Bratislava | Slovakia Phone: +421 2 44 681 417 | Fax: +421 2 4468 1419 Email: sales@srs-group.com | www.srs-group.com ( 16 / 16)

Table of Contents