Advertisement

DC 650 T /
DC 800 T

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DC 650 T and is the answer not in the manual?

Questions and answers

Andy McIntyre
March 17, 2025

Receiver not working from transmitter. Transmitter working OK. Manually door works fine. How do I fix it

2 comments:
Mr. Anderson
March 17, 2025

If the Cardale DC 650 T receiver is not responding to the transmitter, try the following steps:

1. Check the battery – Replace the battery in the hand transmitter if it is flat.
2. Check the aerial – Ensure the aerial is plugged in and properly aligned.
3. Program the transmitter – If no hand transmitter is programmed, follow the manual's procedure to program it (menu stage 1).
4. Check the diagnostic display – If the door does not respond to any impulse generators, refer to the diagnostic display for fault details.
5. Improve signal reception – If the transmitter's range is insufficient, consider using an external aerial accessory.

These steps should help resolve the issue with the receiver not working with the transmitter.

This answer is automatically generated

Andy McIntyre
March 18, 2025

@Mr. Anderson What aerial?

philip stephen morrell
March 23, 2025

door does not close fully, stays open about 40cm

1 comments:
Mr. Anderson
March 23, 2025

The Cardale DC 650 T door may not fully close and stay open about 40 cm due to changes in door mechanics or an incorrect force setting. The possible causes and remedies are:

1. Door mechanics have changed – Have the door checked and adjust the force setting (menu stages 5 and 6).
2. Closing force set too weak – Adjust the force setting.
3. End-of-travel positions incorrectly set – Reset the end-of-travel positions (menu stages 3 and 4).
4. Obstruction before reaching the CLOSE position – Remove the obstruction or reset the CLOSE end-of-travel position (menu stage 4).

These steps should help resolve the issue.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Cardale DC 650 T

  • Page 1 DC 650 T / DC 800 T...
  • Page 2 A = 3050 mm B = 2560 mm C = 2905 mm D = 2960 mm E >= 30 mm F = 0 - 100 mm G = 30 - 50° H >= 140 mm...
  • Page 3 8 x 16 6,3 x 16...
  • Page 4 max. 45°...
  • Page 5 AWG 22 AWG 22 AWG 22 AWG 22 LS 2 LS 2 LS 2 LS 2 LS 2...
  • Page 6 A a C B D 3 sec. F< 400N 50mm...
  • Page 7: General Information

    The product has been subjected to a risk assess- • Technical Data - Disposal ment. The design and execution of the product Operator type: DC 650 T / DC 800 T - Data plate based on this corresponds to state-of-the-art Control: FUTURE III C L - Packaging technology.
  • Page 8: Installation Instructions

    • Installation Instructions Fastening the track to operator head parking position (a) on the left and restore the Slot track (as illustrated) with chain sprocket (2) onto connection between the operator and the door. On Please read these instructions carefully prior to the operator shaft (1a) and screw down with the 4 the next movement, the carriage automatically re- installation!
  • Page 9: Programming The Operator

    • Programming the operator travelling direction is altered. setting can be increased or decreased via buttons and . After setting the value, press button Control elements Now travel by pressing button into the desired door The display shows “6”. The controls for programming the door operator are end position OPEN 17b.
  • Page 10: Terms Of The Guarantee

    Terms of the Guarantee Dear customer, unauthorized modifications shall not assume responsibility for follow-up costs - use of non-original components or removal of the resulting from installation and dismantling, checking The product you have purchased has undergone data plate of parts, freight costs and postal charges nor for extensive testing throughout its manufacture to - mechanical damage (due to being dropped or claims for compensation and lost profit.
  • Page 11: Operating Instructions

    • Maintenance / Checks • Operating Instructions interruption of the light barrier during the opening cycle makes no difference. These Operating Instructions describe how to use The door system must be inspected • Lighting the prodct properly and safely. The safety advice and and tested by a specialist company The lighting switches on automatically whenever a information as well as the accident prevention and...
  • Page 12 Trouble-shooting • Important note: When working on the operator, always pull out the mains plug beforehand!!! Fault/Malfunction Possible cause Remedy Door does not fully close/open Door mechanics have changed Have door checked. Change force setting (menu stages 5 and 6) Set closing/opening force too weak.

This manual is also suitable for:

Dc 800 t

Table of Contents

Save PDF