Related Manuals for LXNAV FlarmLED+
Summary of Contents for LXNAV FlarmLED+
- Page 1 FlarmLED+ Version 1.2 LXNAV d.o.o. • Kidričeva 24, 3000 Celje, Slovenia • tel +386 592 33 400 fax +386 599 33 522 info@lxnav.com • www.lxnav.com...
-
Page 2: Table Of Contents
Important Notices Limited Warranty 1.1.1 Disposal of Old Electrical & Electronic Equipment Flarm end user license agreement Packing Lists Installation LXNAV FlarmLED+ Basics LXNAV FlarmLED+ display at a Glance 4.1.1 LXNAV FlarmLED+ display features 4.1.2 Interfaces 4.1.3 Technical Data System Description Description of FlarmLED+ 5.1.1... -
Page 3: Important Notices
LXNAV retains the exclusive right to repair or replace the unit or software, or to offer a full refund of the purchase price, at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. -
Page 4: Disposal Of Old Electrical & Electronic Equipment
FlarmLED+ display Version 1.21 December 2018 1.1.1 Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. - Page 5 FlarmLED+ display Version 1.21 December 2018 Limitation of use. Firmware, license keys, and data may only be used as embedded 1.2. in and for execution on devices manufactured by or under license from FLARM Technology. License keys and data may only be used in the specific devices, by serial number, for which they were sold or intended.
- Page 6 FlarmLED+ display Version 1.21 December 2018 Manipulation. It is forbidden to intentionally feed artificially generated signals to the FLARM device, its GPS antenna or the external/internal GPS antenna connections, unless agreed with FLARM Technology in writing for limited R&D activities. FLARM Data and Privacy 5.1.
- Page 7 FlarmLED+ display Version 1.21 December 2018 General terms Governing Law. This Agreement shall be governed by and construed in accordance 7.1. with the internal law of Switzerland (to the exclusion of Swiss Private International Law and of international treaties, in particular the Vienna Convention on the International Sale of Goods dated April 11, 1980).
-
Page 8: Packing Lists
FlarmLED+ display Version 1.21 December 2018 Packing Lists FlarmLED+ • Cable • Page 8 of 26... -
Page 9: Installation
FlarmLED+ display Version 1.21 December 2018 Installation The installation of FlarmLED+ is part of the Minor Change covering the installation of the FLARM device and must include an AFM Supplement. The Minor Change for PowerFLARM Core can be acquired here: https://flarm.com/shop/easa-minor-change-approval-mca/ Please refer to chapter 5.6 for detailed wiring instructions. -
Page 10: Lxnav Flarmled+ Basics
FlarmLED+ display Version 1.21 December 2018 LXNAV FlarmLED+ Basics 4.1 LXNAV FlarmLED+ display at a Glance ® FlarmLED+ display is a Flarm compatible device, able to indicate horizontal and vertical direction of a threat. Nearby traffic is displayed visually and acoustically. It’s extremely small size, low power consumption, and has very bright bicolour LED’s. -
Page 11: System Description
FlarmLED+ display Version 1.21 December 2018 System Description 5.1 Description of FlarmLED+ It consists of 6 main parts: Status LEDs • Horizontal direction LEDs • Vertical direction LEDs • Touch pad • Beeper • ALS (Ambient light sensor) • Distance Vertical Horizntal to the... -
Page 12: Status Leds
FlarmLED+ display Version 1.21 December 2018 5.1.1 Status LEDs Status LEDs indicates if connected Flarm device receives any data, transmits data and GPS status. RX status led indicates that Flarm device is receiving something from other Flarm units. TX status led indicates that Flarm device is transmitting data. GPS status led has 3 different modes: Fast blinking mode, means, that FlarmLED+ does not receive anything over serial bus •... -
Page 13: Touch Pad
FlarmLED+ display Version 1.21 December 2018 5.1.5 Touch pad With touching to front side of FlarmLED+, user can adjust volume of beep, turning on/off near mode or adjust initial settings of the display. Initial settings can be configured in setup. 5.1.6 Is Ambient light sensor. -
Page 14: Multi Target In Nearest Modus
FlarmLED+ display Version 1.21 December 2018 indicate Near mode OFF. 5.3.2.1 Multi target in nearest modus If more than one target is in the neighbourhood, the closest target will be displayed with yellow LED permanently. All other targets will blink in yellow colour. Distance and vertical angle will indicate the closest target. - Page 15 FlarmLED+ display Version 1.21 December 2018 Page 15 of 26...
-
Page 16: Undirected Pcas Warning
FlarmLED+ display Version 1.21 December 2018 5.3.5 Undirected PCAS warning If the FlarmLED+ is connected to a device, which also translates transponder signals with ADS-B data into Flarm warnings, you will receive them in the same logic as other FLARM objects. -
Page 17: Setting Up Flarmled
FlarmLED+ display Version 1.21 December 2018 5.4 Setting up FlarmLED+ If we touch LXNAV FlarmLED+ with two fingers for 6 seconds, LXNAV FlarmLED+ will go into setup mode, where following settings can be adjusted: Brightness of LED’s • Units setting •... -
Page 18: Other Indications
FlarmLED+ display Version 1.21 December 2018 Setting Left digit Right digit description descrition Brightness of LED’s A.. automatic (ALS) (default) 0.. Minimum brightness 1.. Medium - 2.. Medium + 3.. Maximum brightness Units setting 0.. km (default) 1.. nm 2.. ml Vertical indicator LED 0.. -
Page 19: Obstacle Database Update
FlarmLED+ display Version 1.21 December 2018 5.5.2 Running Flarm firmware update (2) 5.5.3 Obstacle database update (3) 5.5.4 Diagnostic dump (4) 5.5.5 Restore file system (5) 5.5.6 Internal consistency check (6) Page 19 of 26... -
Page 20: Error Codes From Flarm
FlarmLED+ display Version 1.21 December 2018 5.5.7 Error codes from flarm If any error is present numeric display will blink with an error code. On picture below is code 81, which means No Obstacles. In case error code is having more higher then 0xFF, additionally round LED segment will blink, where number of blinking segments indicates highest number. - Page 21 FlarmLED+ display Version 1.21 December 2018 41 = RF communication 42 = Another FLARM device with the same Radio ID is being received. Alarms are suppressed for the applicable device. 43 = Wrong ICAO 24-bit address or radio ID 51 = Communication 61 = Flash memory 71 = Pressure sensor 81 = Obstacle database (e.g.
-
Page 22: Wiring
FlarmLED+ display Version 1.21 December 2018 5.6 Wiring 5.6.1 FlarmLED+ pinout Pin number Description N.C. (output) Transmit from LXNAV FlarmLED+ RS232 Level (input) Receive to LXNAV FlarmLED+ RS232 Level Ground N.C. 12V DC supply (input) Page 22 of 26... -
Page 23: Flarmmouse - Flarmled
FlarmLED+ display Version 1.21 December 2018 5.6.2 FlarmMouse – FlarmLED+ V7 Flarm Splitter Flarm Power FlarmMouse FlarmLED+ Supply Cable 5.6.3 PowerMouse – FlarmLED+ FlarmLED+ PowerMouse Flarm Power Supply Cable 5.6.4 FlarmBat – FlarmLED+ FlarmLED+ FlarmBat Flarm Power Supply Cable Page 23 of 26... -
Page 24: Cutout
Firmware can be updated via special flarmLED+ update cable, connected to PC through serial interface. You can get flash loader at: https://gliding.lxnav.com/lxdownloads/firmware/ (S7 PC update tool) For the update you need file named _x*.lxfw (x= version nr.) on your computer. - Page 25 FlarmLED+ display Version 1.21 December 2018 Page 25 of 26...
-
Page 26: Revision History
FlarmLED+ display Version 1.21 December 2018 Revision History November 2018 Initial release of this manual November 2018 Reviewed/updated chapters: 4.1,5.2,5.1.2 Added chapters: 5.3.6 November 2018 Added Flarm EULA and installation chapter December 2018 Flarm EULA and misc typos Page 26 of 26...
Need help?
Do you have a question about the FlarmLED+ and is the answer not in the manual?
Questions and answers