Related Manuals for Bison 1800
Summary of Contents for Bison 1800
-
Page 1: Instruction Manual
ELECTRIC HIGH PRESSURE WASHER INSTRUCTION MANUAL Please read this book carefully before operating. -
Page 2: Item Description
APPLICATION High pressure washer mainly used for cleaning and maintaining motor vehicle, project vehicle, project mechanism and agricultural mechanism, such as cleaning car, bulldozer, concrete stirrer and so on, also can be used to clean hotel, showplace, station, dock and so on. ITEM DESCRIPTION WORKING THEORY Motor connect to crank directly, driving piston pump working, water... - Page 3 MAIN TECHNICAL DATA 1800 2500 2600 2900 3600H 3600 Model Work 12MPa 15MPa 20MPa 25MPa 25MPa 25MPa Pressure Max Pressure 13MPa 15MPa 18MPa 20MPa 25MPa 25MPa Rated Power 2.2KW 3.0KW 4.0KW 5.5KW 5.5KW 7.5KW Work voltage Single Single/3 3 Phase...
- Page 4 itself. • To reduce the risk of injury, do not operate the machine near children. • Learn how to stop the machine and release pressure quickly. Be thoroughly familiar with the controls. • Stay alert — watch what you are doing. •...
-
Page 5: Assembly Instructions
• Flow rate of water supply must not fall below 4 GPM (gallons per minute). • Flow rate can be determined by running the water for one minute into an empty 5-gallon container. • The water supply temperature must not exceed 104°F/40°C. •... - Page 6 NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. Hold the location pin in the wheel set backward in horizontal level and press the locating pin into supporting tube until the click is heard, which indicates the pin clutches at the supporting tube.(P1) Until the pin is higher than the thickness of supporting wall.(P2)
-
Page 7: Connect Hose And Water Supply To Pump
using. Machine oil quantity is subject to slightly not too oil lens center line, then install the breather plug. Connect Hose and Water Supply to Pump 1. Attach high pressure hose to gun. Tighten securely. 2. Connect spray wand to gun. Tighten securely. 3. -
Page 8: Connect Power
5. Run water through your garden hose for 30 seconds to clean out any debris. IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 104°F (40°C)). 6. Before connecting water inlet hose to water inlet, inspect inlet screen (A). -
Page 9: Grounding Instructions
GROUNDING Instructions This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. - Page 10 HOW TO USE Turn on the pressure washer (I). The motor starts only if the trigger of the gun is pulled and shuts off when the trigger is released. Read instruction manual carefully before operating this machine, check whether screw, nut loose, oil in crank tank dry. If no oil, shall inject to half, exchange oil-cork with hole.
-
Page 11: Operating And Maintenance
1. Pull back collar on quick–connect and pull current spray tip off. Store spray tips in holder provided on the nozzle extension. 2. Select desired spray tip: •For gentle rinse, select white 40°spray tip. •To scour surface, select yellow 15°or red 0°spray tip. •To apply detergent, select black spray tip. - Page 12 When finished cleaning, release trigger valve, turn off motor (within 3 minutes), because after release trigger valve the will do bypass working, water flowed in the pump body, if too long, will be very hot, broken seal or other parts. Spray pole is made of iron paint chrome, keep carefully when operating, when not using, put the spray gun hung on the pothook, drain out the balance water inside.
-
Page 13: Troubleshooting
TROUBLE SHOOTING Trouble Cause Remedy The motor fails to start 1. No power or socket 1. Check power, repair or when running is not good enough socket automatic stop 2. Switch is broken 2. Change switch 3. No oil in crank tank 3.