Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bison ES1.8-2
Summary of Contents for Bison ES1.8-2
-
Page 2: Item Description
APPLICATION High pressure washer mainly used for cleaning and maintaining motor vehicle, project vehicle, project mechanism and agricultural mechanism, such as cleaning car, bulldozer, concrete stirrer and so on, also can be used to clean hotel, showplace, station, dock and so on. ITEM DESCRIPTION lnpl! J hose... -
Page 3: Main Technical Data
MAIN TECHNICAL DATA MODEL ES1 8-2 ES2 2-2 ES3-2 ES2 2-4 ES3-4 ET2 2-4 ET3-4 ET4-4 ETS 5-4 ET7 5-4 WORK PRESSURE 100-110B, 90-100Bar 110-120Bar 90-100Bar 110-120Ba『 90-100Bar 110-120Ba 186-200Ba 230-250Bai 230-250Ba MAX PRESSURE 130Bar 130Bar 150Bar 130Bar 150Bar 130Bar 150Bar 220Bar 275Bar... -
Page 4: Water Supply (Cold Water Only)
itself. • To reduce the risk of injury, do not operate the machine near children. • Learn how to stop the machine and release pressure quickly. Be thoroughly familiar with the controls. — • Stay alert watch what you are doing. 贮号... - Page 5 Flow of water must not fall below 4 GPM can be determined the water for one minute into container. ° ° must not F/40 washer to draw in water contaminated with etc. drawn into the unit clean water source 五 1.
- Page 6 ＼ ． NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. Hold the location pin in the wheel set backward in horizontal level and press the locating pin into supporting tube until the click is heard, which indicates the pin clutches at the supporting tube.(P1) Until the pin is higher than the thickness of supporting wall.{P2)
-
Page 7: Connect Hose And Water Supply To Pump
using. Machine oil quantity is subject to slightly not too oil lens center line, then install the breather plug. Connect Hose and Water Supply to Pump 1. Attach high pressure hose to gun. Tighten securely. 2. Connect spray wand to gun. Tighten securely. ，... -
Page 8: Connect Power
5. Run water through your garden hose for 30 seconds to clean out any debris. IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 104 ° F (40 ° C)). 6. Before connecting water inlet hose to water inlet, inspect inlet screen (A). -
Page 9: Grounding Instructions
3 Phase Powe Single phase Power 「 EB EB � EB 手 壬 千 士壬壬手 壬 手 令 亡 － 飞 High pressure washer power wire High pressure washer power wire GROUNDING Instructions This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. - Page 10 HOW TO USE Turn on the pressure washer {I). The motor starts only if the trigger of the gun is pulled and shuts off when the trigger is released. Read instruction manual carefully before operating this machine, check whether screw, nut loose, oil in crank tank dry. If no oil, shall inject to half, exchange oil-cork with hole.
- Page 11 1. Pull back calla current sp 「 「 off. Store spray tips in holder on the nozzle extension. 2. Select desired spray •T o scour select •T o . . . select black spray 3. Pull back on insert new spray tip and release collar. on spray tip to make sure it is spray t1p f om 8 to 24 inches (20 to...
- Page 12 When finished turn off motor because valve the will do water flowed in the pump be very broken or other is made of iron when not the spray gun on the drain out the balance water inside. drain out all water in pump, inlet hose from water source, motor about 1 minutes without water source, take...
- Page 13 I Cause Trouble The motor fails to start I 1. No power or socket or when automatic 2. Switch is broken I 2. 3. No oil in crank tank I 3. 4. Voltaqe too low motor Motor burn out No jet from nozzle or 1.
-
Page 14: Pump Parts List
PUMP PARTS LIST N高氓 H,me N.me 如 如e 心． Hame 心． 如 如 1应t O-nn1 乃 Nut 0-dng O-n叩 2 wmher 「，如LOil史l 氓plu, o-n,屯 旺gubtor氐dle cover 3 V斗亿Op 如ll七」”“'b匹 WM，比「 • C=“心比lo, 0-rio, ◄ • 扣 · 艾 0-rl屯 沁rlngw”her 肋lt Byp芯＄ml代...
Need help?
Do you have a question about the ES1.8-2 and is the answer not in the manual?
Questions and answers