Samsung WF-R1061 Service Manual page 66

29 DRUM 4E :front Water level sensor
WASHER loading inferiority
(MODEL washing
NAME : machine
Q1*3*) error
30 DRUM 5E :front Water being not drained
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
31 DRUM OE :front 3E OVER-FLOW
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
32 DRUM UE :front 4E UNBALANCE ERR
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
33 DRUM HE1 : front E5 WATER HEATER ERR
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
34 DRUM HE : front E6 WATER HEATER ERR
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
35 DRUM 1E :front E7 Water level sensor
WASHER loading ERR
(MODEL washing
NAME : machine
Q1*3*) error
36 DRUM cE : front E8 Abnormal water tem-
WASHER loading perature ERR
(MODEL washing
NAME : machine
Q1*3*) error
37 DRUM 8E : front E9 Water leakage ERR
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
38 DRUM tE :front E9 Water leakage ERR
WASHER loading
(MODEL washing
NAME : machine
Q1*3*) error
All manuals and user guides at all-guides.com
AS rerecomm
ended
AS rerecom-
mended
General
consulting
General
consulting
General
consulting
AS rerecom-
mended
AS rerecom-
mended
AS rerecom-
mended
AS rerecom-
mended
AS rerecom-
mended
63
This may be Disconnect the water supply hose and check
happened whether there is a foreign material inserted in it.
when there And then request an engineer's inspection.
is any foreign
material inside
the water
supply and
drain valve
or the interior
components of
the prodcuts
do not operate
normally.
Water level
sensor or
mother
rotation.
It may be Check the installation of drain hose and then
occurred when if there is no trouble request an engineer's
the drain hose inspection.
is go over the Clean the fi lter of pump-drain motor. Guided by
threshold or instruction-manual.
water is not
drained.
It may eb
occurred when
the The fi lter
of pump-drain
moder is fulled
with dregs,
It may be a After Draining the water power off and on and
case that the operate again. If it dose not work after so doing
supply water request an engineer's inspection.
level is not
detected.
It may be hap- Level the machine or arrange the entangled
pened when clothes. If it does not worked even after so doing
the fl oor of the request an engineer's inspection.
installed palce
is not fl at or
the clothes are
entangled.
It may happen Use the proper amount of detergent and power
when the off the machine till the temperaure is cooled
boiling tem- down.
peratuer rised And if it does not work even after so doing
rapidly. (It is request an engineer's inspection.
also because
too much
detergent are
used.)
It may appear In this case you are recommended our
when it dose engineer's inspection.
not reach to
the set tem-
perature within
a certain time.
It may happen In this case you are recommended our
when there is engineer's inspection.
a trouble in air
hose or water
level sensor.
Check Check whether the cold water is supplied
whether the through the cold water supply hole and if
hose for hot it doesn't work after so doing request an
and cold water engineer's inspection.
is connected
to the water
supply hole.
Check In this case you are recommended our
whether there engineer's inspection.
is foreign ma-
terial inserted
in the drain
fi lter.
Check In this case you are recommended our
whether there engineer's inspection.
is foreign ma-
terial inserted
in the drain
fi lter.