Related Manuals for Orion 5Q740
Summary of Contents for Orion 5Q740
- Page 1 USER’S MANUAL MODEL No.: 5Q740 BEFORE USING THIS COLOR MONITOR, READ AND OBSERVE ALL OF THIS USER’S MANUAL...
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTION CAUTIONS FCC RF INTERFERENCE STATEMENT INSTALLATION RESOLUTION CONTROLS AND FUNCTIONS REAR VIEW SPECIFICATIONS TROUBLE SHOOTING GUIDE T his Moni tor was Man ufac tured by ISO 90 01 Cer tifi ed Fac tory... -
Page 3: Safety Instruction
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 5. - Page 4 SAFETY INSTRUCTION 13. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to service personnel. 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions.
-
Page 5: Cautions
CAUTIONS Removal of the back cover should be carried out only by qualified personnel. This display monitor contains high voltage inside. To prevent shock or fire hazard. Do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases. -
Page 6: Fcc Rf Interference Statement
FCC RF INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 7: Installation
INSTALLATION NO TOOLS ARE REQUIRED TO INSTALL THE MONITOR. SIMPLY FOLLOW THE INSTRUCTIONS OUTLINED IN THE FOLLOWING PAGE. 1. INSTALLING THE TILT/SWIVEL STAND 1) Align the stand with the slots in the bottom of the monitor and insert the Tilt/Swivel Stand into the slots. 2) Push the Tilt/Swivel Stand firmly toward the front of the monitor until the latches click into the locked position. -
Page 8: Resolution
RESOLUTION 1. RECOMMENDED SIGNAL TIMING CHART Horizontal Vertical Clock Poles Resolution Frequency Frequency Frequency (KHz) (Hz) (MHz) (H / V) 31.469 70.087 25.175 (+ / -) IBM(640 * 350) 31.469 70.087 28.322 (- / +) IBM(720 * 400) 31.469 59.941 25.175 IBM(640 * 480) (- / -) -
Page 9: Controls And Functions
CONTROLS AND FUNCTIONS B.DEGAUSS BUTTON POWER INDICATOR(LED) A. POWER SWITCH C.SELECT BUTTON D. ADJUST BUTTONS (DOWN & UP) A. POWER SWITCH( Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights when the power is turned ON. - Page 10 CONTROLS AND FUNCTIONS C. SELECT BUTTON If you want to adjust to the monitor, push the SELECT button. If you push the button, one of the following two OSD menu is displayed for control on screen. You can use the UP or DOWN button to make selection for each function. If you push this SELECT button once more, this allows you to activate the desired adjustment with the change of adjustment bar color black to violet.
- Page 11 CONTROLS AND FUNCTIONS ( u p & down) D. ADJUST The Adjust button allows user to choose the icons (controls) in the menu. Pressing the adjust button up or down will step through all available adjustment icons (controls). In addition this adjust button can be used to adjust the icons (controls) that is selected and activated via the select button.
- Page 12 CONTROLS AND FUNCTIONS 3. OSD MENU DESCRIPTION OSD MENU 1 H POSITION (Horizontal Position) Moves images horizontally on screen left( up ) or right(down„ ) . H SIZE (Horizontal Size) Â Increases(up„ ) or decreases(down ) size of image horizontally V POSITION (Vertical position) Moves images vertically on screen up or down.
- Page 13 CONTROLS AND FUNCTIONS OSD MENU 2 RECALL Resets the control functions back to the original factory preset values. In order for the Recall function to work, the timing must fall under one of the factory preset timing modes. ROTATION Adjusts the tilt of image. LANGUAGE Selects a language among ENGLISH, DEUTSCH, FRANÇAIS, ESPAÑOL, ITALIANO, JAPANESE.
-
Page 14: Rear View
REAR VIEW E. AC INLET Power cord connection. NOTE Power cord is used as main power disconnect device in this product. F. D-SUB CONNECTOR OF SIGNAL CABLE Connect to the analog RGB signal output connector of video card. E. AC INLET F. -
Page 15: Specifications
SPECIFICATIONS 15inch Dynamic focus 90°£ Deflection 0.28mm Dot Pitch 1280x1024 Non Interlaced @60Hz HORIZONTAL : 30-70KHz VERTICAL : 50-150Hz VIDEO: Analog (0.7Vp-p) 75 SYNC: Horizontal(4.0 Vp-p), Vertical(4.0 Vp-p) Preset : 265mm X 195mm Full : 282mm X 212mm 487mm X 463mm X 447mm (Carton Box) Net Weight : 12.0Kg Gross Weight : 14.0Kg... -
Page 16: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE TROUBLE TROUBLE SHOOTING TIP No image on display screen 1. Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip. 2. Power switch should be in the ON position and LED is lit.