Download Print this page
Parrot Anafi Assembly/Disassembly Manual

Parrot Anafi Assembly/Disassembly Manual

Hide thumbs Also See for Anafi:

Advertisement

Quick Links

How to assemble and
disassemble Anafi

Advertisement

loading
Need help?

Need help?

Do you have a question about the Anafi and is the answer not in the manual?

Questions and answers

Summary of Contents for Parrot Anafi

  • Page 1 How to assemble and disassemble Anafi...
  • Page 2 Prerequisites The best way to repair ANAFI is to use Parrot official drones repair kit. You will need the cruciform as well as the Torx 5 (T5) in order to carry out this procedure. Parrot repair kit Anafi disassembly process Remove the battery from the drone.
  • Page 3 Remove both screws from the bottom of the drone at the arms junction. Lift the bottom cover from the front of the drone, then push it toward the rear to remove it. ANAFI assembly and disassembly processes...
  • Page 4 Pull the ventilator to remove it from its slot and remove the LED connector, near the ventilator. Remove antennas from the motherboard. Antennas on the middle of the motherboard are linked to the rear feet; the side antennas are plugged to the front feet. ANAFI assembly and disassembly processes...
  • Page 5 Remove the plastic holder from the motherboard by pulling on the plastic stamp, then slide the holder. Remove the gimbal connector from the motherboard. Unplug the micro coaxial wire from the motherboard. ANAFI assembly and disassembly processes...
  • Page 6 Remove the four rubbers gently: Parrot recommends you hold the motherboard during the process, to stop rubbers from falling from their support. Once rubbers are removed, unplug the GPS antenna which can be found on hidden face of the motherboard.
  • Page 7 Remove the vertical camera from the support by pushing gently on it. Remove the three screws under each arm of the drone. ANAFI assembly and disassembly processes...
  • Page 8 Pull on the bottom cover of each arm to remove them. Remove the two screws from the GPS cover (orange circle) then push on the button above located the gimbal to remove the cover (red circle). ANAFI assembly and disassembly processes...
  • Page 9 Retract the arms towards the body of the drone before removing the black plastic holder of each hinge. Push the lower side of each hinge to remove them. Caution: a washer will fall off from each hinge when removed, make sure that you do not lose them. ANAFI assembly and disassembly processes...
  • Page 10 Unplug motors by pulling the connectors out of their sockets. Caution: Do not pull on the wires. Remove the arms carefully, one after the other: make sure that antenna cables do not get stuck with other cables. ANAFI assembly and disassembly processes...
  • Page 11 There is a rubber part with holes letting wires go through to connect it from the gimbal to the motor card: the small hole is dedicated to the flex wire; the larger one is meant to receive the micro coaxial wire. Remove the gimbal from the body. ANAFI assembly and disassembly processes...
  • Page 12 Remove the motor card by pushing it slightly toward the bottom of the drone If you need to change the motor, remove both antennas and the reflector simultaneously. Then, unscrew the three screws from under the motor to remove it and replace it. ANAFI assembly and disassembly processes...
  • Page 13 Flex wire and micro coaxial wire holder GPS holder Foot (x4) Bottom cover Antenna + reflector + wire GPS card Arm hinges Motherboard holder for motor wire antenna and micro coaxial wire holder Arm washer ANAFI assembly and disassembly processes...
  • Page 14 Screw the motor card to the center body. The LED wire and the ventilator must be placed between the motor card and the support (on the right side, seen from the bottom). Number Associated part LED wire Ventilator ANAFI assembly and disassembly processes...
  • Page 15 Slide the motor wire inside the large hole of the top part of the arm. On the low part of the arm, insert simultaneously the antenna and the reflector in their respective slots. You can let the antenna wire free for now. Numéro Elément du drone Antenna Reflector ANAFI assembly and disassembly processes...
  • Page 16 Put the screws back to stick the upper and bottom parts together. Insert arms in their dedicated slots on the central body and insert both antenna wire and motor wire in the bottom part of the drone. Numéro Drone part Motor Wire Antenna wire ANAFI assembly and disassembly processes...
  • Page 17 -Put the screws back on the larger extremities of the hinge (one on the top side; one on the lower side). -Repeat to install each arm. -Position antenna wires toward the front of the drone and the motor wires toward the back of the drone. ANAFI assembly and disassembly processes...
  • Page 18 Pull the coaxial wire gently to keep enough length to plug it. Screw the two screws on the front side of the gimbal before plugging the flex wire. ANAFI assembly and disassembly processes...
  • Page 19 Position the GPS card back and screw it; check that the antenna wire is not stuck. Position the GPS cover back and screw it. To place the motherboard back correctly, start by plugging back the GPS antenna. ANAFI assembly and disassembly processes...
  • Page 20 Position the motherboard back in place by placing it on the two rubbers of the front of the drone, then on the two rubbers on the rear of the drone. Make sure antenna wires are above the LED wire and ventilator. ANAFI assembly and disassembly processes...
  • Page 21 Make sure there is enough free wire to let the gimbal move in any direction. Insert the bottom cover, starting from the front side, before clipping it; make sure no wire is visible. Conclude the assembly process by screwing the bottom protection back. ANAFI assembly and disassembly processes...