Table of Contents
Advertisement
Instructions
™
Pulse
For use with Pulse Fluid Management System Components only.
Not approved for use in explosive atmospheres or hazardous locations. For Indoor use
only.
Part Nos.:
Part No.
Approvals
24Z978
25D454
Important Safety
Instructions
Read all warnings and instructions
in this manual and all related Pulse
manuals. Save all instructions.
Both devices contain ConnectCore6 i.MX6 WiFi/Bluetooth Radio, IC: 1846A-CCIMX6B.
HUB 24Z978 contains XBee Pro S2C TH Radio, IC: 1846A-PS2CTH.
HUB 25D454 contains XBee S2C TH Radio, IC: 1846A-S2CTH.
Both devices contain FCC ID MCQ-CCIMX6B. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received, including interference that may cause
undesired operation.
HUB 24Z978 contains FCC ID MCQ-PS2CTH. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received, including interference that may cause
undesired operation.
HUB 25D454 contains FCC ID MCQ-S2CTH. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received, including interference that may cause
undesired operation.
HUB
I
3A5414A
EN
Advertisement
Table of Contents
Related Manuals for Graco 24Z978
Summary of Contents for Graco 24Z978
-
Page 1: Important Safety Instructions
• This device must accept any interference received, including interference that may cause undesired operation. HUB 24Z978 contains FCC ID MCQ-PS2CTH. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: •... - Page 2 Pulse HUB Overview and Component ID Pulse HUB Overview and Component ID The Pulse HUB is a self-contained computer with the Pulse Fluid Management Software preloaded. It also is the Personal Area Network (PAN) host used for RF communication with other Pulse system components (meters, Pump Air Control [PAC’s], Tank Level Monitors [TLM’s]).
-
Page 3: Installation
Installation Installation Locate the Pulse HUB in the main part of the shop, high on a wall or on the ceiling, in a location that provides an unobstructed line of sight, near the meters, PACs, and/or tank level monitors. Always comply with all applicable local, state and national fire, electrical and safety regulations. -
Page 4: Connecting Hub To Lan (Local Area Network)
Installation Connecting HUB to LAN HUB Installation (Local Area Network) During installation zip-ties or screws can be used to allow relocation of the HUB to There are two options available for connect- optimize RF communication. ing the HUB to the LAN: Ethernet Cable (C) or WiFi. -
Page 5: Operation
Operation Operation Once the Pulse HUB is installed, verify that the power light (D) (F . 5) is ON and the HUB is functioning correctly. When the green power light (D) is illuminated it indicates the unit is receiving AC power. The status of the Pulse Fluid Management Software is indicated by the HUB Status Light (G) (F... -
Page 6: Main Dashboard
Software Software Main Dashboard Dispenses: Based on user’s selections, displays as a list of pending, active, completed and canceled dispenses. Tanks: Displayed as a percentage, reports the amount of fluid remaining in the tank. The fluid is measured from the bottom of the tank to the full level. Reports: The Pulse Fluid Management System generates a variety of reports related to data it collects while the system is operating. -
Page 7: Software Setup
Software Software Setup Application Settings: General system settings • General System Settings: Language, Units of Measurement, PIN size, Inactivity Duration • Time Settings • Business Schedule • E-mail Settings • Network Settings Device Settings: Device configuration and firmware settings • Fluids •... -
Page 8: Frequently Asked Questions
Software Frequently Asked Questions Q. What does the meter do if the batteries are removed when you are dispensing? A. If you are not using work orders, the accumulated dispense amount is saved. When fresh batteries are installed, the meter powers up. The next time a dispense ends, two entries are entered in the dispense complete log;... -
Page 9: Troubleshooting
TLMs within RF range of meters and TLMs Weak or no RF signal Changes/obstructions in RF Add Graco Extender to pathway (i.e., vehicles, Pulse system. Order Graco overhead doors, etc.) Part No. 17F885 - US, 17F776 - EU, 17F887 - UK, 17F888 - ANZ. - Page 10 Parts Parts Part No. Description 131310 FLASH DRIVE (not shown) 17S458 ANTENNA 17S658 POWER ADAPTER (not shown) ENCLOSURE LABEL, serial number 17E169 CABLE, Ethernet 3A5414A...
-
Page 11: Technical Specifications
100 - 240 VAC line voltage 50-60 Hz 0.05A To HUB 5 Vdc (0.5 amps typ) RF Frequency Band 2400 - 2483.5 MHz Maximum RF Transmit Power Model 24Z978 63 mW (18 dBm) Model 25D454 6.3 mW (8 dBm) Dimensions 3A5414A... -
Page 12: Graco Extended Hub Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twenty four months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.