Audio Specifications; Dimension And Weight - NAD C 328 Owner's Manual

All specs are measured according to IHF 202 CEA 490-AR-2008 standard. THD is measured using AP AUX 0025 passive filter and AES 17 active filter.

AUDIO SPECIFICATIONS

ANALOG IN/HEADPHONE OUT
THD (20 Hz – 20 kHz)
Signal-to-Noise Ratio
Frequency response
Output impedance
ANALOG IN/SUBWOOFER OUT
THD (20 Hz – 20 kHz)
Signal-to-Noise Ratio
Frequency response
Gain
Output impedance
ANALOG IN/SPEAKER OUT
Continuous output power into 8 ohms
and 4 ohms
THD (20 Hz – 20 kHz)
Signal-to-Noise Ratio
Gain
Clipping power
IHF dynamic power
Peak output current
Damping factor
Frequency response
Channel separation
Input sensitivity (for 40 W in 8 ohms)
Standby power
<0.005 % at 1 V out
>100 dB (A-weighted, 32 ohms, ref. 2V
out, unity gain)
±0.3 dB (20 Hz - 20 kHz)
11 ohms
<0.005 % at 1 V out
>100 dB (A-weighted, 32 ohms, ref. 2V
out, unity gain)
±0.2 dB (20 Hz - 20 kHz)
17 dB
200 ohms
40W (ref. 20 Hz-20 kHz at rated THD, both
channels driven)
<0.03 % (100 mW to 40 W, 8 ohms and
4 ohms)
>95 dB (A-weighted, 500 mV input, ref.
1 W out 8 ohms)
37 dB
>50 W (at 1 kHz 0.1 % THD)
8 ohms: 90 W
4 ohms: 166 W
>18A (in 1 ohm, 1 ms)
>100 (20 Hz - 20 kHz)
±0.3 dB (20 Hz - 20 kHz)
>85 dB (1 kHz)
>70 dB (10 kHz)
250 mV
<0.5 W
PHONO IN/SPEAKER OUT
THD (20 Hz – 20 kHz)
Signal-to-Noise Ratio
Frequency response (RIAA deviation)
Channel separation
Input sensitivity (for 40 W in 8 ohms)
DIGITAL IN/SPEAKER OUT
THD (20 Hz – 20 kHz)
Signal-to-Noise Ratio
Frequency response
Gain
Channel separation

DIMENSION AND WEIGHT

Gross dimensions (W x H x D)
Net weight
Shipping weight
* - Gross dimension includes feet, volume knob and extended rear panel terminals.
Specifications are subject to change without notice. For updated documentation and features, please
check out www.NADelectronics.com for the latest information about C 328.
REFERENCE
SPECIFICATIONS
<0.03 % (200 mW to 40 W, 8 ohms and
4 ohms)
>75 dB with IHF MM cartridge
(A-weighted, ref. 5mV input, 1 kHz and
1W output in 8 ohms)
±0.3 dB (20 Hz - 20 kHz)
Note: The RIAA response is consistent with
a pre-emphasis that is rolled off at 50kHz
by a second order filter, such as used in
Neumann cutting lathes.
>80 dB (1 kHz, 8 ohms, 50 mV input,
13W out)
>60 dB (10 kHz, 8 ohms, 50 mV input,
13W out)
3.6 mV
<0.03 % (100 mW to 40 W, 8 ohms and
4 ohms)
>95 dB (A-weighted, -12 dBFS input, ref.
1W out in 8 ohms)
±0.3 dB (20 Hz - 20 kHz)
47 dB (Vrms/FS)
>80 dB (1 kHz)
>70 dB (10 kHz)
435 x 70 x 285 mm
17 1/8 x 2 13/16 x 11 1/4 inches
4.9 kg (10.8 lbs)
5.9 kg (13.0 lbs)
11