Preparation; Mounting The Battery; Inserting The Sd Memory Card; Powering The Unit On - komamura KC-2000MK II Owner's Manual

6.

Preparation

6-1. Mounting the Battery

Install a fully-charged battery as follows:
① Remove the rear cover.
② Slide the locking pin away from the battery hold in the direction of the red arrow, as shown below.*
③ Insert the battery into the battery hold.
④ Slide the locking pin back toward the battery hold to secure the battery.
⑤ Replace the rear cover in its original position.
*
To remove the battery, slide the locking pin away from the battery. The battery will pop out.
Battery cannot be charged in this camera. Fully charge the battery first in its own charger.

6-2. Inserting the SD Memory Card

Insert the SD memory card as follows:
① Remove the rear cover.
② Insert the SD card, with its metal contacts facing
forward and to the right, into the SD card slot.
③ Push the card into the slot until you hear a 'click'.
④ Replace the rear cover in its original position.
*
To remove the SD card, push the card in. The card will unlatch and pop out.
● Before using a SD card for the first time:
The SD memory card must be formatted.
→Please see the description about Setup Page 4/4
on P20 of this manual.
Note. 1
The following SD Memory Cards have been tested on KC2000:
Model Class
SD （SDHC）
4 and up
Write Once SD （Tamper-Proof）
-
We do not guarantee functionality for all commercially-available SD Memory Cards.
The following SD Memory Card manufacturers are recommended:
・ Panasonic ・ Toshiba
Please do NOT delete the files recorded on this camera using your PC. Doing so in some cases will
deteriorate the card's ability to record and playback video. If this happens, copy the files onto your PC
first, then re-format the SD Memory Card in this camera.
Note 2
Total recording time on a SD memory card will vary depending on the amount of scene details.
Recording time available on a single battery charge will depend on the temperature, the number of
charge cycles on the battery, and the charge method. We recommend that you plan ahead and have
enough SD memory cards and batteries for twice the expected recording time.
POWER SWITCH DC POWER PORT
Shown with REAR COVER off
SD CARD
ACCESS
INDICATOR
SD CARD SLOT
BATTERY
SD CARD
LOCKING PIN
Metal contact side
● Caution: Do not remove the SD card,
battery nor the AC adaptor while the SD
Card Access Indicator is flashing.
● Never remove the SD card while
recording nor during playback.
Capacity Notes
32GB
Toshiba ： SD-K01G
1GB
(Not fo Video Record/Playback)
・ SanDisk
6
Note 3
Folders are automatically created on the SD memory card to store data.
Sill image files are stored inside the "DCIM/100KC200" folder.
REAR COVER
Video files are stored inside the "MOVIE" folder.*
（*"MOVIE" folder is not created on Write-Once （ Tamper-Proof） SD cards.）

6-3. Powering the Unit On

This product may be powered either by the battery or by the AC adapter through the DC POWR PORT.
If both the battery and the AC adapter are present, the camera takes its power from the DC POWER PORT.
Turn the camera ON or OFF by pressing and holding the POWER SWITCH for more than 2 seconds.

6-4. Power On and Preflight Checks

① Press and hold the POWER SWITCH for more than 2 seconds.
② Video image will appear in the VIEWFINDER (or on the HDMI monitor if one is connected).
The display will say "BOOTING" while the unit is booting up.
③ Once the "BOOTING" message disappears the camera is ready for use.
The camera will always boot into RECORD mode.
After boot, the display will look like this.
the ICONS won't be displayed on the HDMI monitor.）
ICON DISPLAY AREA MENU/MESSAGE DISPLAY AREA
➡
AE MODE ICON
➡
AE LEVEL ICON
➡
WB MODE ICON
➡
DNR MODE ICON
➡
FOG MODE ICON
➡
BLC MODE ICON
AE MODE ICON Indicates the current AE (Automatic Exposure) MODE setting. If shutter speed priority is
selected, the shutter speed will be shown instead.
AE LEVEL ICON Indicates the current AE LEVEL setting. When the menu is not showing, the level may be
adjusted by moving the MENU SELECT / CURSOR KEY button left or right.
WB MODE ICON Indicates the current WHITE BALANCE MODE setting.
DNR MODE ICON Indicates the current DYNAMIC NOISE REDUCTION MODE setting.
FOG MODE ICON Indicates the currnt FOG MODE setting.
BLC MODE ICON Indicates the current BACK LIGHTING CORRECTION MODE setting.
POWER ICON Indicates the power source currently in use, with a battery icon for battery and DC power
plug icon for external DC power source.
（If ICON DISPLAY for the HDMI monitor is turned off in the MENU setting,
ICON DISPLAY AREA
FULL
AUTO
AE
0
ATW
DNR
HIGH
FOG
OFF
BLC
OFF
7
➡
POWER ICON
➡
SD CARD ICON
➡
VIDEO
VIDEO FILE ICON
HXXXX
➡
PHOTO
PHOTO FILE ICON
HXXXX