Related Manuals for VisAccess VXS-10
Summary of Contents for VisAccess VXS-10
- Page 1 Sales: 30 Habarzel Street, Tel Aviv 69710 Israel Tel : 972 3 6456789, Fax 972 3 6456891 Technical Dept.: 35 Hamelacha St. Carmiel 20100 Tel: 972 4 9081115 Fax: 972 4 9081116 VXS-10 User Guide pp.2-5 VXS-10 Installation Guide pp.6-11...
-
Page 2: User Programming
Thank you for choosing the VisAccess VXS-10. We are confident that this product will serve your needs for years to come. The VisAccess VXS-10 is an electronic access control solution for a single access point, such as a main door in an apartment building or individual office doors. The controller relay activates a lock or electromagnetic strike (EMS), when a valid proximity key (tag) is presented to the reader located outside the protected area. - Page 3 • To select the ADD mode press the “MODE” button and present the master key to the reader until the ADD LED starts flashing, indicating that the VXS-10 is ready to add a key. • Once you present a key to the internal reader, the key will be added and its number will be displayed for a few seconds.
- Page 4 • Press the “MODE” button for the next programming mode or simply wait 5 seconds for the system to time out and revert to normal operation. 2.8. Setting The Password The VXS-10 is shipped from the factory with the following default password: It is recommended to change the password during installation!
-
Page 5: Normal Operation
3.1. Valid Key Detection If a key is presented to the external reader, the VXS-10 will search the list of valid keys in its memory. If the key is found, the VXS-10 will light the green LED and activate the output relay to open the lock for the pre-programmed unlock time. -
Page 6: Hardware Installation
The locking device may be connected to the VXS-10 in several ways: • EMS – powered by the VXS-10 – connect the EMS as shown in Fig. 2. • EMS powered by its own power supply - connect via the VXS-10 Dry contact, normally open terminals as shown in Fig. 3. - Page 7 2.2 Setting The Master Key The VXS-10 has one master key. The installer needs to assign one of the proximity keys as a master key and program it into the controller memory. To assign a master key: • Press the “Mode” button.
- Page 8 • You may press “F1” at any time to exit without saving the new unlock time. 2.5 Wiring connections Figures 2, 3, and 4 show the wiring connections of the VXS-10 to the power supply and the locking devices (Electro Magnetic Strike or Magnetic Lock). It is recommended to connect an Earth ground wire to the EMS case or to actual earth ground if available.
- Page 9 – Connect the device to an outlet on a circuit different from the one which supplies power to the receiver. – Consult the dealer or an experienced radio/TV technician. WARRANTY VisAccess Ltd. And/or its subsidiaries and its affiliates ("the The Manufacturer does not represent that its Product may not be Manufacturer") warrants its products hereinafter referred to as "the compromised and/or circumvented, or that the Product will prevent any Product"...
- Page 10 Power + VXS-10 Power Supply Power - (AC or DC) Use Separate power supplies for VXS-10 and EMS (normally open relay) Use Separate power supplies for VXS-10 and Maglock (normally closed relay) relay Ground black 12V Power Red Gr LED...
- Page 11 VXS-10 Controller Mounting Template Cable hole 10mm Screw holes VXS-10 Control Panel Scale 1:1 Cable hole Screw hole 10mm ©VISACCESS Ltd. 1999 VXS-10 DE6270U (REV. 0, 6/99)