Table of Contents
Advertisement
o
•
_
•
ee
motor spec faCahons and e ectrmcalrequmrements
Th_is machine
is designed
to use a 3450
RPM moto_
only
Do
not
use any
motor
that
r._r_s faster'
than
3450
RPM,
It is wired
for
operation
on t10-t20
vo_ts, 60 Hz.
_dter-
nating
current.
IT
MUST
NOT
BE
CONVERTED
"TO
OPERATE
ON
230
VOI.TS.
EVEN
THOUGH
SOME
OF
THE
RECOMMENDED
MOTORS
ARE
DUAL
VOLTAGE,
THESE
CRAFTSMAN
MOTORS
HAVE
BEEN
FOUND
TO BE ACCEPTABLE
FOR USE ON
THIS
TOOL.
11/2
3450
110-120
12!6
1/2
3450
110-!20
1218
3/4
3450
t10-120
!219
3/4
3450
110-120
t226
CAUTION:
Do not use blower
or washing
machine
motor_
or
any
motor
with
an automatic
reset overload
protector
as their
use may be hazardous.
CONNECTING
TO POWER SOURCE OUTLET
This
machine
must
be grounded
while
ip use to protect
the operator
from electric
shock,
This
_x_wer tool
is equipped
with
a 3-conductor
cord
and
grounding
type
plug
which
has a grounding
prong
Jisted by
Underwriters'
Laboratories
Association.
The
ground
conductor
has _ green
jacket
and is attached
to the tooi
housing
at
one
end
and
to
the
ground
prong
in
the
attachment
p)ug at the
other
end.
This
p]u[_ requi:re_s
a
mating
3-conductor
grounded
type
outJ_t as s.how_l.
if
the
ot_t}et
you
are
pla:n:ning
to use
for
this
power
tool
is
of
the
two
pretty
type
DO
NOT
REMOVE
OR
ALTER
THE
GROUNDING
PRONG
IN
ANY
MANNER.
Use
an
adat_)te_
as showr_
an(t
a_ways
connect
the
grounding
!ug
to
k r_c:twn g_ouf_{t.
It is recommende(J
that
you
have
a qualified
electrician
replace
the TWO
prong
outlet
with
a properly
grounded
THREE
prong
out_et:.
An adapter
as shown
below
is available
for connecting
plugs
to 2-prong
_ec{:ptactes,
The
green grounding
lug
extending
from
the adapter
must
be connected
to a permanent
ground
s_ch as to a properly
grounded
outlet
box.
Plug power
cord
into
a 110-120V
properly
grounded
type
outlet
protected
by
a 15.amp,
time
delay or CircuitSaw_r
fuse or circuit
breaker.
If you
are not sure
that your
outlet
is propet!¥
g, ounded,
have it checked
by a qualified
electrician,
WARNING:
DO
NOT
PERIMIT
FINGERS
TO TOUCH
THE
TERMINALS
OF PLUGS
WHEN
INSTALLING
OR
REMOVING
THE
PLUG
TO
OR
FROM
THE
OUTLET.
WARNING:
IF
NOT
PROPERLY
GROUNDED
THIS
POWER
TOOL
CAN
_INCUR THE
POTENTIAL
HAZARD
OF ELECTRICAL
SHOCK.
PARTICULARLY
WHEN
USED
IN
DAMP
LOCATIONS
IN PROXIMITY
TO PLUMBING,
IF
AN
ELECTRICAL
SHOCK
OCCURS
THERE
ISTHE
POTENTIAL
OF
A SECONDARY
HAZARD
SUCH
AS
YOU_R
HANDS
CONTACTING
THE
CUTTING
BLADE.
If power
cord
is worn
or cut,
or damaged
in any way,
have
it replaced
immediately.
PROPERLY
__
GROUNDED
OUTLET.,_
i
J
@
3-PRONG
PLUG
GROUNDING
PRONG
NOTE:
The adapter
illustrated
is for use only if you already
have a properW
grounded
2-prong
receptacle.
The
use of any
extension
cord
will
,cause some
loss of
power.
To keep
this
to
a minimum
and to prevent
over-
heating
and motor
burn-out,
use the table
below
to deter-
mitre the mirdmtjm
wire
size (A.W.G.)
extension
cord.
Use
only
3 wire extension
cords
which
have 3-prong
grounding
type
plugs and
3-pole
receptacles
which
accept
the too&
plug.
Extensior_
Cord
Length
Wire
Size
A,W.G,
Up to 1OO Ft.
14
!00
200
Ft,
!2
200-400
Ft.
8
CHECK
MOTOR
ROTATION
WARNING:
FOR
YOUR
OWN
SAFETY,
MAKE
SURE
PLUG
tS NOT
CONNECTED
TO POWER
SOURCE
OUT
LET
WHEN
CHA_%IGtNG
MOTOR
ROTATION.
The
mote."
must
rotate
COUNTERCLOCKWISE
whet
viewed
from
the
s_qaft
enci _o which
you
wil!
mount
th_
pu!_ey,
(See page
1'O).
_tf it does not,
change the dire_,:._ior
acco_-diqg to the
ir;structions
furnished
with
the motor.
Hide quick links:
Advertisement
Table of Contents
