Download  Print this page

Advertisement

CONTENTS
SD-253
ENG
GER
BEL
RSA
AUST
NZL
Page
2
8
11
22
23
25
27
© 2002 Matsushita Electric Industrial Co., Ltd. All
rights
distribution is a violation of law.
ORDER No. KAD0207508C2
Automatic Bread Maker
reserved.
Unauthorized
Page
29
31
33
35
36
37
copying
and

Advertisement

Table of Contents

   Summary of Contents for Panasonic SD-253

  • Page 1: Table Of Contents

    ORDER No. KAD0207508C2 Automatic Bread Maker SD-253 AUST CONTENTS Page Page 1 Operating Instructions 8 REPLACEMENT PARTS (RSA) 2 TROUBLESHOOTING CHART 9 REPLACEMENT PARTS (AUST) 3 DISASSEMBLY PROCEDURE 10 REPLACEMENT PARTS (NZL) 4 WIRING CONNECTION DIAGRAM 11 PACKAGING (ENG) 5 REPLACEMENT PARTS (ENG)
  • Page 2: Operating Instructions

    SD-253 1 Operating Instructions...
  • Page 3 SD-253...
  • Page 4 SD-253...
  • Page 5 SD-253...
  • Page 6 SD-253...
  • Page 7 SD-253...
  • Page 8: Troubleshooting Chart

    SD-253 2 TROUBLESHOOTING CHART Note : The causes of unsuccessful baking vary and can be divided roughly into user-side problems and bread maker problems. Most problems are caused by the user. Therefore, it is very important to obtain detailed information from customers regarding their conditions of using the bread maker and to specify whether the problem lies with the user or the bread maker.
  • Page 9 SD-253 Check point Diagnosis Remedy Connection of the heater terminals Check the connection of the heater terminals. Make a proper connection. <Reference value> (If no problem is found with the connection) Replace the heater. Resistance of the heater (in normal status) 230V: 96Ω...
  • Page 10 SD-253 Symptom Cause Remedy The bread rises too much. The amount of sugar is excessive. Reduce the amount of sugar. The amount of yeast is excessive. Reduce the yeast to a proper level. A business-use flour with too much protein has Reduce the amount of yeast.
  • Page 11: Disassembly Procedure

    SD-253 3 DISASSEMBLY PROCEDURE 3.1. Top lid 1. Remove the dispenser cover assembly and the dispenser assembly from the top lid. 2. Remove the hinge screw from the back of the body. 3. Lift the top lid and slide it to the left to remove it.
  • Page 12 SD-253 3.2. Control panel assembly 1. Remove the two screws labeled F. Parts Name Screw F 2. Remove the control panel assembly by pressing the side of Control panel Ass’y Fig.5 Fig.4 3.3. P.C. board A assembly 1. Remove the connectors from the solenoid and the lead wire A unit.
  • Page 13 SD-253 3.4. Solenoid 1. Remove a screw from the solenoid. 2. Remove the solenoid holder plate and spring A. Fig.8 Parts Name Screw Solenoid holder plate Spring A Control panel Ass’y Solenoid Ass’y 3.5. Bottom plate Before turning the body upside down, remove the kneading blade, bread pan assembly, measuring spoon, and measuring cup.
  • Page 14 SD-253 3.6. Power cord 1. As shown in the figure, turn the body upside down with the power cord stored inside the angel unit to prevent damage to the cord. Fig.10 Parts Name Power cord Body Ass’y 3.7. Body 1. Remove the six screws labeled F.
  • Page 15 SD-253 3.8. Power cord 1. Disconnect the power cord connectors. 2. Push the cord bushing A and push out the power cord B. Fig.14 Parts Name Power cord Fig.13 Cord bushing Parts Name Angle Angle Cord bushing Power cord 3.9.
  • Page 16 SD-253 3.10. Ground wire A assembly 1. Remove the screw and the spring washer that secures the ground wire A assembly. 2. Raise the two claws of the ground plate up with the flat- blade screwdriver. 3. Remove the ground plate from the heater terminal.
  • Page 17 SD-253 3.12. Heater 1. Remove the "Faston" terminal from the heater. 2. Raise the two claws of the ground plate up with the flat- blade screwdriver. 3. On the outside of the heater case, detach the three claws that secure heater bobbin B.
  • Page 18 SD-253 3.13. lnner lid 1. Remove the three screws that secure the inner lid. 2. Insert a thin flat-blade driver into the space between the top lid and the inner lid (six locations) to move it up and take out the inner lid.
  • Page 19 SD-253 3.15. Belt, Pulley B, and Connector lower unit 1. Remove the belt by rotating pulley B. 2. Remove the lock nut and then pulley B and the lock washer. 3. Remove the U-cripe and pull out the connector lower unit.
  • Page 20 SD-253 3.17. Bread pan 1. Remove the three screws from the mounting shaft Ass’y to remove it. 2. Remove the packing. Caution: · Attach the bread pan to the mounting shaft Ass’y while aligning them with the mark. · When replacing the mounting shaft Ass’y, replace the packing and the three screws with new ones.
  • Page 21 SD-253 3.19. Location of production code The production code is marked on the bottom plate (bottom side) of the main body. Fig.26 Parts Name Production code Bottom plate...
  • Page 22: Wiring Connection Diagram

    SD-253 4 WIRING CONNECTION DIAGRAM Parts Name Parts Name For Angle 16 Flat cable Heater 17 Connector Kneading motor 18 Sensor (W/Fuse) Ground wire A 19 Wire (Orange) Wire (Yellow/Green) 20 Solenoid Ass’y Lead wire B (white) 21 Yellow line...
  • Page 23: Replacement Parts (eng)

    SD-253 5 REPLACEMENT PARTS (ENG) 5.1. Parts Location (ENG)
  • Page 24 SD-253 5.2. Replacement Parts List (ENG) Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ADA39E142-0S Dispenser cover Ass´y Caution ADE01R117-0S Angle Unit Water label & protect Seal rubber tape ADY02E142-W Caution label ADA24E142 Power cord Ass´y...
  • Page 25: Replacement Parts (ger)

    SD-253 6 REPLACEMENT PARTS (GER) 6.1. Parts Location (GER)
  • Page 26 SD-253 6.2. Replacement Parts List (GER) Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ADA39G142-0S Dispenser cover Ass´y Caution ADB10E142 P.C.B.holder label & ADE01R117-0S Angle Unit Water Seal protect rubber tape ADY02G107-W...
  • Page 27: Replacement Parts (bel)

    SD-253 7 REPLACEMENT PARTS (BEL) 7.1. Parts Location (BEL)
  • Page 28 SD-253 7.2. Replacement Parts List (BEL) Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ADA39R142-0S Dispenser cover Ass´y Caution ADB10E142 P.C.B.holder label & ADE01R117-0S Angle Unit Water Seal protect rubber tape ADY02E142-W...
  • Page 29: Replacement Parts (rsa)

    SD-253 8 REPLACEMENT PARTS (RSA) 8.1. Parts Location (RSA)
  • Page 30 SD-253 8.2. Replacement Parts List (RSA) Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ADA39K142-0S Dispenser cover Ass´y Caution ADB10E142 P.C.B.holder label & ADE01R117-0S Angle Unit Water Seal protect rubber tape ADY02K107-W...
  • Page 31: Replacement Parts (aust)

    SD-253 9 REPLACEMENT PARTS (AUST) 9.1. Parts Location (AUST)
  • Page 32 SD-253 9.2. Replacement Parts List (AUST) Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ADA39R142-0S Dispenser cover Ass´y Caution ADE01R117-0S Angle Unit Water label & protect Seal rubber tape ADY02E142-W Caution label ADA24R132 Power cord Ass´y...
  • Page 33: Replacement Parts (nzl)

    SD-253 10 REPLACEMENT PARTS (NZL) 10.1. Parts Location (NZL)
  • Page 34 SD-253 10.2. Replacement Parts List (NZL) Ref. Part No. Part Name & Description Ref. Part No. Part Name & Description Remarks Remarks ADA39R142-0S Dispenser cover Ass´y Caution ADB10E142 P.C.B.holder label & ADE01R117-0S Angle Unit Water Seal protect rubber tape ADY02E142-W...
  • Page 35: Packaging (eng)

    SD-253 11 PACKAGING (ENG) Parts Name Protection board Cushion Ass’y (Upper) Measuring spoon Measuring cup Lid protection sheet Kneading blade B Unit Bread pan Ass’y Body Ass’y Plug 10 Power cord Ass’y 11 Operating Instructions set 12 Carton 13 Cushion Ass’y (Lower)
  • Page 36: Packaging (aust, Nzl)

    SD-253 12 PACKAGING (AUST, NZL) Parts Name Protection board Cushion Ass’y (Upper) Measuring spoon *Only for NZL Measuring cup Lid protection sheet Kneading blade B Unit Bread pan Ass’y Body Ass’y Plug 10 Power cord Ass’y 11 Operating Instructions set 12 Carton 13 Cushion Ass’y (Lower)
  • Page 37: Packaging (ger, Bel, Rsa)

    SD-253 13 PACKAGING (GER, BEL, RSA) Parts Name Protection board Cushion Ass’y (Upper) Measuring spoon Measuring cup Lid protection sheet Kneading blade B Unit Bread pan Ass’y Body Ass’y Plug 10 Power cord Ass’y 11 Operating Instructions set 12 Carton 13 Cushion Ass’y (Lower)

Comments to this Manuals

Symbols: 0
Latest comments: