Fisher & Paykel GD75IA1 Installation Instructions Manual
Hide thumbs
Also See for GD75IA1:
- Installation instructions and user manual (16 pages) ,
- Troubleshooting (2 pages)
Table of Contents
Advertisement
Quick Links
Installation instructions
Before you begin
Please read these installation instructions completely and carefully.
• The following installation instructions are intended as a general guide.
• Please ensure that the waste disposal unit is installed according to local building codes for your area.
• Installation is recommended to be done by a qualified plumber or installer.
• Product failure due to improper installation is not covered under the Warranty.
Preparation
Removing an existing waste disposer, if installed
1. Disconnect electrical power supply to existing disposer.
2. Remove old disposer or sink flange assembly.
3. Inspect drain line. If it is heavily coated with hardened grease and accumulations, clear out the build-up using a
plumber's rod or auger.
4. Remove old sealing materials and gaskets from sink opening, both top and bottom.
https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions
Updated: Fri, 01 Mar 2019 07:04:48 GMT
Powered by
1
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel GD75IA1
Summary of Contents for Fisher & Paykel GD75IA1
-
Page 1: Installation Instructions
3. Inspect drain line. If it is heavily coated with hardened grease and accumulations, clear out the build-up using a plumber’s rod or auger. 4. Remove old sealing materials and gaskets from sink opening, both top and bottom. https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by... -
Page 2: What You Will Need
2. Sink flange 3. Rubber gasket 4. Flange ring 5. Protector ring 6. Mount ring 7. Screw clamp 8. Hopper with splash guard 9. Dishwasher discharge inlet 10. Drain housing https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by... - Page 3 11. Reset button 12. Built in air-switch 13. Lower shell 14. End Bell (Electrical Connections) 15. Power cord Fig 1. 3-801t Mount System https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by...
-
Page 4: Installing The Waste Disposer
This will allow the sink flange, mount ring, and protector ring to separate (fig 3). Use the flat blade screwdriver as a lever if required. Fig. 3 Disassembling the mounting system https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by... - Page 5 This will not damage the disposer in any way, but may take some time to grind, over the course of several uses. https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by...
- Page 6 Fig. 7 Connecting the discharge elbow Please do not remove clamp and splash guard from hopper. Both parts are factory installed and installation ready. Fig. 8 Lubricate the rubber splash guard https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by...
- Page 7 Return to step 10 to realign the waste disposer before repeating steps 11-13. Ensure that the reset button is readily accessible after installation of the waste disposer. Fig. 11 Connecting the drain outlet https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by...
-
Page 8: Installing The Air-Switch (Optional)
5. Connect the other end of the PVC tubing to the air switch outlet, located on the underside of the waste disposer (fig.14). Fig. 14 Connecting tube to air switch outlet https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by... -
Page 9: Controlling The Waste Disposer By A Wall Mounted Switch
4. Whilst the waste disposer is running, disconnect the PVC tubing from the air switch outlet on the underside of the waste disposer. 5. Turn the waste disposer off using the wall mounted switch. The waste disposer can now be turned on and off using the wall mounted switch. https://producthelp.fisherpaykel.com/nz/Clean/Dishwashing_Accessories/GD75IA1/User_Guide_GD75IA1/02_Installation_instructions Updated: Fri, 01 Mar 2019 07:04:48 GMT Powered by...