The ScyTek Galaxy 3000 Plus is a state-of-the-art vehicle security system featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come.
Remote Transmitter Description Button 1 Button 3 The Galaxy 3000 Plus is supplied with two 5-button Remote Transmitters used to control system operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons.
Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations.
Remote Arming The system monitors 6 independent areas ( zones ) while armed: doors, hood, trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. ·...
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat for 20 seconds. LED Flashes (60 seconds): 1 flash optional sensor 2 flashes shock sensor...
Panic Mode In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 3 seconds. · The alarm will sound. ·...
To set the Emergency Override Code: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch 4 times. ·...
Extended F F eatures Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle.
Remote Sensor Disable When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong weather conditions that could cause the sensors to trigger, the sensor inputs can be temporarily bypassed using the Remote Transmitter, preventing possible false alarms. To disable the sensor inputs : 1.
1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit Two 5-Button Remote Transmitters Siren Shock Sensor Harnesses 16-Pin main harness • 4-Pin shock sensor harness • 3-Pin door lock harness •...
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc.
16-Pin Main Harness Pin 1 BROWN WIRE: Siren Output (+) 3A. The Brown wire must connect to the siren’s red wire. The Black siren wire must be grounded. Pin 2 BLACK WIRE: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away any paint or dirt to insure the best possible ground.
Starter Defeat Connectors Using a volt/ohm meter locate the starter wire (normally a heavier gauge wire) at the ignition switch. This wire will show +12V only during cranking. When this wire is cut the vehicle will be unable to start. Locate the BROWN starter disable wire included with the wiring harness and cut in half.
Jumper Selections Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the polarity jumpers will be visible next to the parking light and dome light relays. Set the jumpers for the correct polarity output as described below, then reassembly the main unit case.
Entering System Programming To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch the number times equal to the System Parameter you want to change. ·...
Branch Feature 1. Arm Mode 2. Auto Rearming Mode 3. Arming Chirps 4. Ignition Door Locking 5. Ignition Door Unlocking 6. Door Unlock Pulse 7. Door Lock Pulse Length 8. Passive Door Locking 9. Passive Arming Entry Delay 10. Ignore Open Door Report 11.
Page 22
10. Ignore Open Door Report. Bypasses the open zone warning chirps for vehicles equipped with a residual dome light circuit that remains on for a period of time after closing the door. 11. Horn Chirps with Arm & Disarm / Anti-Carjack with Valet Reset. This dual program branch activates the horn chirps during Arming and Disarming, and activates one of two Anti-Carjacking options.
Page 23
18. Start in Valet Mode.* Selects whether or not the vehicle can remote start while in the valet mode. *Requires the optional ScyNet Network Remote Car Start Module. 19. Remote Start Program.* This dual program branch sets the engine mode for Gas or Diesel, and learns the vehicle’s RPM threshold.
Door L L ock D D iagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages. Negative Trigger Positive Trigger Reverse Polarity Vacuum Adding Actuators Page 20 - Galaxy 3000 Plus...
Two S S tage D D oor L L ock D D iagrams The Galaxy 3000 Plus is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door.
Page 26
Two S S tage D D oor L L ock D D iagrams c c ont’d Two Stage Reverse Polarity Two Stage Adding Actuators Page 22 - Galaxy 3000 Plus...
FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation Technical I I nformation Galaxy 3000 Plus - Page 23...