Advertisement
Quick Links
Advertisement
Related Manuals for Pepperl+Fuchs WirelessHART Adapter
Summary of Contents for Pepperl+Fuchs WirelessHART Adapter
- Page 1 Quick Start Guide WHA-ADP* WirelessHART-Adapter Firmware Update Instructions...
-
Page 2: Table Of Contents
WHa-adP* Table of Content uick tart uide Table of Content Getting Started ..................6 1.1. Requirements .................... 6 1.2. Preparation ....................6 1.3. Establishing a Connection ................. 6 1.4. Firmware Update ..................12 1.5. Example of a path: ..................14... - Page 3 WHa-adP* Table of Content uick tart uide...
-
Page 4: Getting Started
Firmware Update Package (accessible via Pepperl+Fuchs sales contact) 1.2. Preparation The WirelessHART Adapter should be powered by a battery of type W-BAT-B2-Li A connection to the adapter is necessary for the firmware update. Depending on the conditions at site, the connection can either be established with the help of a HART Modem or wirelessly via a WirelessHART Gateway. - Page 5 WHa-adP* Getting Started uick tart uide Figure 1. Now the device catalog will open. Search for the device called HART Communicati- on from CodeWrights GmbH, select it and press OK. Figure 2. Now the HART interface has been added to your project. Right click on the HART Com DTM in the project tree and select Add device again.
- Page 6 Figure 3. Now the WirelessHART Adapter DTM can be added. Navigate to the WHA-ADP DTM’s. Depending on the adapter revision you have available, you need to choose between WHA-ADP and WHA-ADP Rev. 2. Don’t worry if you’re not sure about the revision of your device.
- Page 7 WHa-adP* Getting Started uick tart uide Afterwards your project tree should look like this: Figure 4. Now the HART Com DTM needs to be configured at first. Double click at the HART Com DTM (labeled with COM1 or something similar), afterwards the DTM should open on the right side of the screen: Figure 5.
- Page 8 The start address as well as the end address should be set to 15, this is the default value of every new WirelessHART Adapter. The communication timeout can be increased in order to avoid communication pro- blems when the adapter needs to be waken up from deep sleep.
- Page 9 WirelessHART Adapter DTM and select Connect: Figure 8. Double click at the WirelessHART Adapter DTM in order to open the online view. It will take a moment until the adapter wakes up from sleep mode and the connection symbol in the project tree gets green.
-
Page 10: Firmware Update
Figure 10. 1.4. Firmware Update Now you have ensured that a connection to the WirelessHART Adapter is available. To find out which firmware version the adapter has currently installed, right click at the WirelessHART Adapter DTM in the project tree and select Additional functions ->... - Page 11 WHa-adP* Getting Started uick tart uide Now a new window will open. The current firmware version is displayed at the bot- tom: Figure 12. Important Note If you’re trying to install firmware update 02.40.01 ensure that your adapter has firm- ware version 02.40.00.
-
Page 12: Example Of A Path
WHa-adP* Getting Started uick tart uide 1.5. Example of a path: The downloaded and extracted firmware package in this example is located in the download-folder. Use the Windows Explorer to navigate to the location where the file is located and click into the address bar. This will reveal the full path: Figure 13. - Page 13 The firmware update procedure usually takes 20 to 30 minutes with a HART Mo- dem. Wirelessly via the WirelessHART Gateway the procedure can take several hours, depending on the network topology. Do not terminate the connection to the WirelessHART Adapter before this message appears: Figure 17.
- Page 14 Subject to modifications · © Pepperl+Fuchs Printed in Germany · DOCT-6110...