Table of Contents
Advertisement
Quick Links
Installation Instructions
Model RCC-2/R and RSE-1
Remote Control Centers
INTRODUCTION
The Model RCC-2/R Remote Command Center
from Siemens Industry, Inc. (See Figure 1)
provides the option to remotely annunciate and
control MXL and MXL-IQ system status. The
RCC-2/R and RSE-1 provide for mounting and
control of the PIM-1 printer interface module.
The following modules come already installed in
an RCC-2/R:
• Keypad
• LCD Display
• ANN-1 Driver Board
• PS-5N7 Power Supply
The following modules come already installed in
an RSE-1:
• ANN-1 Driver Board
• PS-5N7 Power Supply
The RCC-2/R has a mounting location for an
optional PIM-1. The RSE-1 has the same
Mounting and requires the PIM-1.
The RCC-2/R comes with a clear lens on a
secure door. This limits access to the control of
the system or the display. The door is secured
with a T-45 lock set.
Figure 1
RCC-2/R Remote Command Center
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
P/N 315-099160-8
OPERATION
The keypad on the RCC-2/R operates the same
as the MKB in the MXL enclosure. See Section 3
of the MXL Installation, Operation and Mainte-
nance Manual, P/N 315-092036, for the com-
plete operating instructions for the control panel.
INSTALLATION
Always remove all power before installa-
tion, first the battery and then the AC.
Setting the Network Address
Before installing the RCC/RSE, set the network
address on S1-SW1 and S1-SW2 of the ANN-1
board. Refer to Table 1 for switch settings. (See
also Setting the Network Address in Section 2,
INSTALLATION of the MXL/MXLV Manual, P/N
315-092036.)
TABLE 1
SWITCH SETTINGS ON THE ANN-1
ADDRESS SETTINGS FOR:
SWITCH
248
Open-
S1-SW1
OFF
Open-
S1-SW2
OFF
Closed-
S1-SW3
ON
Closed-
S1-SW4
ON
Closed-
S1-SW5
ON
NOTE: Switches S1-SW3 and S1-SW4 are for
future use. Switch S1-SW5 is used to
select supervision.
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
249
250
251
Closed-
Open-
Closed-
ON
OFF
On
Open-
Closed-
Closed-
OFF
ON
ON
Closed-
Closed-
Closed-
ON
ON
ON
Closed-
Closed-
Closed-
ON
ON
ON
Closed-
Closed-
Closed-
ON
ON
ON
Advertisement
Table of Contents
Related Manuals for Siemens RCC-2/R
Summary of Contents for Siemens RCC-2/R
- Page 1 PIM-1. The RSE-1 has the same mounting and requires the PIM-1. TABLE 1 The RCC-2/R comes with a clear lens on a SWITCH SETTINGS ON THE ANN-1 secure door. This limits access to the control of the system or the display. The door is secured ADDRESS SETTINGS FOR: with a T-45 lock set.
- Page 2 Setting Supervision 2. Pull all field wiring into the backbox and dress the wiring to the approximate location Use switch S1-SW5 on the ANN-1 to select or to which it will go. Install field wiring to the deselect supervision. If your ANN-1 has a switch PS-5N7 (Refer to PS-5N7 Installation with position 1 indicated on the left-hand side, Instructions, P/N 315-092729).
- Page 3 PS-5N7 ANN-1 LCD DISPLAY RCC-2/RSE-1 BACKBOX COVER PIM-1 (OPTIONAL) ANNUNCIATOR PANEL RCC-2/RSE-1 OUTER DOOR Figure 2 RCC-2/R Exploded View PS-5N7 ANN-1 RSE-1 BACKBOX PIM-1 (REQUIRED) RSE-1 OUTER DOOR Figure 3 RSE-1 Exploded View...
- Page 4 NOTE: The RCC/RSE MUST have an earth ground connected to the chassis. Wire shield or conduit is not an acceptable ground. Use any available unused, unpainted stud for chassis grounding. Figure 4 RCC-2/R, RSE-1 Dimensions DO NOT USE PSR-1 DO NOT USE...
- Page 5 CABLE P/N 600-290505 POWER TO MOM-4 MMB-2 / SMB-2 PSR-1 CHASSIS P7 FOR NET-7 SHIELD SHIELD 1 2 3 4 CABLE P/N 555-190967 9 10 11 12 13 14 NET-7 EOLR MOM-4 120 OHM, 1/4W, 5% P/N 140-820150 PS-5N7 (INSTALLED IN AN SUPERVISED RCC-2/RSE-1 POWER LIMITED...
- Page 6 This page is intentionally blank.
- Page 7 This page is intentionally blank.
- Page 8 This page is intentionally blank. Siemens Industry, Inc. Siemens Building Technologies, Ltd. Building Technologies Division Fire Safety & Security Products Florham Park, NJ 2 Kenview Boulevard Brampton, Ontario P/N 315-099160-8 L6T 5E4 Canada...
Need help?
Do you have a question about the RCC-2/R and is the answer not in the manual?
Questions and answers