Table of Contents
Advertisement
2
Range
Channel
700m
Ultra Low
Video
Latency
Full HD
5GHz
Frequency
High Definition
EU Environmental Protection
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with you local authority or retailer
for recycling advice.
IP
Streaming
RX
RX
Double RX
CVW Beamlink-Duo
2TX-to-1RX Wireless HD Video Transmission System
User Manual
This user manual applies to:
Transmitter:7060
Receiver:3062
User Manual V1.0
Advertisement
Table of Contents
Related Manuals for CVW BeamLink-Duo
Summary of Contents for CVW BeamLink-Duo
- Page 1 Range Channel 700m CVW Beamlink-Duo Ultra Low Video Streaming Latency 2TX-to-1RX Wireless HD Video Transmission System Full HD 5GHz Frequency High Definition Double RX User Manual EU Environmental Protection This user manual applies to: Waste electrical products should not be disposed of with household waste.
-
Page 2: Table Of Contents
Thank you for choosing CVW's professional wireless HD audio 目录 and video transmission product. Read the following precautions carefully before using this product: About the User Manual * Do not use this product for a long time in the sun or dusty place. -
Page 3: About The User Manual
This product supports switching between two operating modes, namely standard mode and RTSP streaming mode. In standard mode, this product supports About the User Manual 2TX-to-1RX and 2TX-to-2RX, and the video outputs interface are HDMI and 3G-SDI. In RTSP streaming mode, this product supports 2TX-to-1RX and 2TX-to-2RX, This Manual details the product specifications, instructions for use, and the video streaming interface is LAN port(RJ45) .. -
Page 4: Structure & Interface
Structure & Interface Transmitter Key Operation Operation Description Function TX: 7060 SONY NPF Battery dock “L” (low-gain) mode: Applicable for close-range(<200m/656ft Antenna Interface OLED Display & LOS) and strong interference environments, with strong anti-interference ability. After switching to L mode, the “L” character Press the will be displayed on the OLED display. - Page 5 RX: 3062 Receiver Key Operation Operation Description Function Antenna Interface After the receiver switches the frequency Frequency Short press channel about 1S , the OLED display of the channel receiver and transmitter will display the new the “CH/WPS” switching button about 1S frequency channel about 1S number after...
-
Page 6: Product Installation
Product Installation For transmitter 1. Please install all the antennas on the transmitter and make them in a fan shape as shown in the picture. Distance>1m 3. Please connect the transmitter and camera with SDI or HDMI cable. 3G-SDI Input 2. - Page 7 B: Vertical placement Receiver Installation A: Horizontal placement 1. Please install all the antennas on the receiver, and make them in a fan shape as shown in the picture. Place the receiver at a height of around 1.5 to 2 meters above floor. install the affiliated metal stand...
- Page 8 4. The receiver can be powered by both the V-mount battery and DC-IN port via Product Application the affiliated power adapter. If the mentioned two types of power supply are connected at the same time, the lithium battery is prioritized in power supplying, and the battery will switch to the power adapter for power supplying automatically Point-to-Point mode after the battery power is exhausted.
-
Page 9: Oled Display Description
OLED Display Description Streaming mode In streaming mode, the 2 channel video sources are sent to the 2 channel TX:7060 transmitters via HDMI or SDI. The receiver will receive the RTSP protocol Signal Icon network signals from the 2 channel transmitters and send them to the Gain Mode embedded switch console for display through the network port. -
Page 10: Functional Instructions
Functional Instructions RX:3062 Tally function Insert the Tally light into the transmitter’s Tally output interface first, then connect the switch console to the receiver’s Tally input interface, Frequency point and then control the Tally light of the four transmitters through the switch CH2 WPS L console. - Page 11 Streaming Function Tally light input interface: R595 Tally1 When using the functions in streaming mode, the transmitter needs to switch to streaming mode. At this time, the word “RTSP” is displayed on the transmitter’s OLED display, the SDI and HDMI at the receiver have no video output, and the image is transmitted to the streaming media R587 Tally2...
- Page 12 Open internet browser, and enter transmitter’s encoder or receiver’s decoder IP address in the address bar to enter the parameter settings page. All transmitter’s encoder and receiver’s decoders need to be configured one by one, please refer to the following configuration case. Transmitter Encoder Case (transmitter 2): IP ETHADDR Transmitter IP address(192.168.1.111~112).
-
Page 13: Wireless Software Upgrade
Wireless Transmission Module Upgrading First, connect the computer to the LAN port of the receiver; Then enter the device’s WiFi IP (wireless transmission module IP) in the Each transmitter has one wireless transmission module, and the software address bar to enter the login page: upgrading needs to be implemented on each transmitter. -
Page 14: Product Specifications
Product Specifications Select the “Upgrade” option in the “System” column. ITEM TX:7060 RX:3062 5190MHZ, 5230MHZ 5755MHZ 5795MHZ Frequency Optional：5270MHZ 5310MHZ 5510MHZ 5550MHZ 5590MHZ, 5630MHZ, 5670MHZ Antenna 4*4 MIMO 5dBi External antenna Modulation mode OFDM Transmission Power 17dBm ≤- 28dB 70dBm Receiving Sensitivity ≤- Bandwidth... -
Page 15: Troubleshooting
Trouble Shooting Precautions Trouble Solutions 1. If transmitter or/and receiver use HDMI cable:(a~f) a. Do not plug in or pull out the HDMI cable of the transmitter and receiver Lift the transmitter and receiver as high as possible, during normal use. to 1.5-2m or more;... - Page 16 3. When using the device, be sure to install the antenna before turning on the power. Failure to do so may result in damage to the device. 4. When used, the surrounding environment will affect the quality of wireless transmission. Poor operating environment may cause image sound disorder, such as picture pause, noise, etc.
Need help?
Do you have a question about the BeamLink-Duo and is the answer not in the manual?
Questions and answers