Table of Contents
Advertisement
Congratulations on owning a Scag mower! This manual contains the operating
instructions and safety information for your Scag mower. Reading this manual
can provide you with assistance in maintenance and adjustment procedures to
keep your mower performing to maximum efficiency. The specific models that
this book covers are listed on the inside cover. Before operating your machine,
please read all the information enclosed.
© 2009
Scag Power Equipment
Division of Metalcraft of Mayville, Inc.
OPERATOR'S
MANUAL
Freedom Z
Models:
SFZ36-17KA
SFZ36-20BS
SFZ48-19KA
SFZ48-26BS
SFZ52-19KA
SFZ52-26BS
SFZ61-28BS
PART NO. 03243 Rev.2
PRINTED 10/2009
PRINTED IN USA
Advertisement
Table of Contents
Related Manuals for Scag Power Equipment FREEDOM Z SFZ36-17KA
Summary of Contents for Scag Power Equipment FREEDOM Z SFZ36-17KA
- Page 1 The specific models that this book covers are listed on the inside cover. Before operating your machine, please read all the information enclosed. © 2009 Scag Power Equipment Division of Metalcraft of Mayville, Inc. OPERATOR’S MANUAL...
- Page 2 FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY OR DEATH. • Read this manual completely as well as other manuals that came with your mower. • DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down).
-
Page 3: Table Of Contents
Table of Contents SECTION 1 - GENERAL INFORMATION 1.1 INTRODUCTION ...1 1.2 DIRECTION REFERENCE ...1 1.3 SERvICING THE ENGINE AND DRIvE TRAIN COMPONENTS ...1 1.4 SYMBOLS ...2 SECTION 2 - SAFETY INFORMATION 2.1 INTRODUCTION ...3 2.2 SIGNAL WORDS ...3 2.3 BEFORE OPERATION CONSIDERATIONS ...3 2.4 OPERATION CONSIDERATIONS ...4 2.5 ROLL-OvER PROTECTION SYSTEM ...6 2.6 MAINTENANCE CONSIDERATIONS &... - Page 4 SECTION 6 - ADJUSTMENTS 6.1 PARKING BRAKE ADJUSTMENT ...21 6.2 TRAvEL ADJUSTMENTS ...22 6.3 THROTTLE CONTROL AND CHOKE ADJUSTMENTS ...23 6.4 BELT ADJUSTMENT ...23 6.5 BELT ALIGNMENT ...23 6.6 CUTTER DECK ADJUSTMENTS ...24 6.7 ELECTRIC CLUTCH ADJUSTMENT ...26 SECTION 7 - MAINTENANCE 7.1 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS ...27 7.2 HYDRAULIC SYSTEM ...28...
-
Page 5: General Information
USE ONLY SCAG APPROvED ATTACHMENTS AND ACCESSORIES. Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. See Section 8, Paragraph 8-1. For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. -
Page 6: Symbols
SYMBOLS SYMBOL DESCRIPTION Choke Parking Brake On/Start Off/Stop Falling Hazard Fast Continuously Variable - Linear Pinch Point 481039S Hour meter/Elapsed Operating Hours STT MODELS Seat must be installed under the seat hold down bracket during installation. Failure to secure the seat under the hold down bracket could result in serious injury or death in a roll over. -
Page 7: Safety Information
Section 2 INTRODUCTION Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. -
Page 8: Operation Considerations
If the operator(s) or mechanic(s) cannot read English or Spanish, it is the owner's responsibility to explain this material to them. DO NOT wear loose fitting clothing. Loose clothing, jewelry or long hair could get tangled in moving parts. Do not operate the machine wearing shorts; always wear adequate protective clothing including long pants. - Page 9 Section 2 To prevent tipping or loss of control, start and stop smoothly, avoid unnecessary turns and travel at reduced speed. Use caution when operating the mower on an incline with the optional grass catcher installed. When using any attachment, never direct the discharge of material toward bystanders or allow anyone near the machine while in operation.
-
Page 10: Roll-Over Protection System
ROLL-OvER PROTECTION SYSTEM WARNING The seat belt must be securely fastened during operation. Failure to do so could cause serious injury or loss of life. This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. -
Page 11: Maintenance Considerations & Storage
Section 2 MAINTENANCE CONSIDERATIONS & STORAGE Never make adjustments to the machine with the engine running unless specifically instructed to do so. If the engine is running, keep hands, feet, and clothing away from moving parts. Disengage drives, lower implement, set parking brake, stop engine and remove key or disconnect spark plug wire to prevent accidental starting of the engine when servicing or adjusting the machine. -
Page 12: Safety And Instructional Decals
Section 2 SAFETY AND INSTRUCTIONAL DECALS 483405 483505 483402 481568 483633 483406 Failure to follow these instructions could result in serious injury or death. DO NOT operate machine on 483425 steep slopes or near drop offs. Avoid sharp and/or quick turns. -
Page 13: Specifications
Section 3 ENGINE General Type ...Heavy Duty Industrial/Commercial Gasoline Brand ...Briggs & Statton, Kawasaki Horsepower: (Scag Model SFZ36-17KA) ... 17 HP (Spec.#FH541V-AW00-R) (Scag Model SFZ48-19KA, SFZ52-19KA) ... 19 HP (Spec.# FH580V-AW00-R) (Scag Model SFZ36-20BS) ... 20 HP (Spec# 40G7770117B1) (Scag Model SFZ48-26BS, SFZ52-26BS) ...26 HP (Spec.# 44P7770117E1) (Scag Model SFZ61-28BS) ... -
Page 14: Cutter Deck
Travel Speed: Forward ...0-8 MPH Reverse ...0-5 MPH -NOTE- The machine will travel at 8 mph for transport purposes. For best cutting performance the forward travel speed should be adjusted depending upon the cutting conditions. CUTTER DECK Type ... Floating, Adjustable, Anti-Scalping, Hybrid Design Combines Out-Front and Belly-Mount Designs Construction ...10-Gauge top with 11-Gauge reinforcement throughout True Cutting Width: 36 ...36"... -
Page 15: Operating Instructions
Section 4 OPERATING INSTRUCTIONS CAUTION Do not attempt to operate this mower unless you have read this manual. Learn the location and purpose of all controls and instruments before you operate this mower. CONTROLS AND INSTRUMENT IDENTIFICATION Before operating the mower, familiarize yourself with all mower and engine controls. -
Page 16: Safety Interlock System
Hourmeter (Figure 4-1). Indicates the number of hours the engine has been operated. It operates whenever the engine is running. Has preset maintenance reminders for engine and hydraulic system oil changes. Will start flashing scheduled maintenance 2 hours before preset time and continue flashing until 2 hours after. -
Page 17: Starting The Engine
Section 4 Check interlock system for proper operation. (See Section 4.2.) Check tire pressure. Adjust pressure if necessary. (See Section 7.10.) STARTING THE ENGINE CAUTION DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway”... -
Page 18: Engaging The Deck Drive (Cutter Blades)
REvERSE TRAvEL CAUTION Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower. CAUTION Before backing up, observe the rear for persons and obstructions. -
Page 19: Hillside Operation
Section 4 HILLSIDE OPERATION WARNING DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. -
Page 20: Moving Mower With Engine Stopped
If the discharge chute becomes clogged, shut off the engine and remove the ignition key. Using a stick or similar item, dislodge the clogged material. Then resume normal mowing. 4.11 MOvING MOWER WITH ENGINE STOPPED To “free-wheel” or move the mower around without the engine running, place the dump valve levers in the FREE- WHEEL position. -
Page 21: Towing (Optional Hitch Accessory) (Not Available For Sfz36)
Section 4 Insert the pin into the cutting height index at the desired cutting height. Push forward on the deck lift foot lever, hold in place and lift up on the deck release lever. See Figure 4-4. Slowly release the foot pedal. -
Page 22: Troubleshooting Cutting Conditions
TROUBLESHOOTING CUTTING CONDITIONS CONDITION STRINGERS - OCCASIONAL Low engine RPM BLADES OF UNCUT GRASS Ground speed too fast Wet grass Dull blades, incorrect sharpening Deck plugged, grass accumulation Width of Deck Belts slipping SGB020 STREAKING - STRIPS OF Dull, worn blades UNCUT GRASS IN CUTTING PATH Incorrect blade sharpening... - Page 23 Section 5 TROUBLESHOOTING CUTTING CONDITIONS (CONT'D) CONDITION U N E v E N C U T O N F L AT GROUND - WAvY HIGH-LOW APPEARANCE, SCALLOPED CUT, OR ROUGH CONTOUR Width of Deck SGB020 UNEvEN CUT ON UNEvEN GROUND - WAvY APPEARANCE, HIGH-LOW SCALLOPED CUT, OR ROUGH CONTOUR Width of Deck...
- Page 24 TROUBLESHOOTING CUTTING CONDITIONS (CONT'D) CONDITION SCALPING - BLADES HITTING DIRT OR CUTTING vERY CLOSE TO THE GROUND Width of Deck SGB022 STEP CUT - RIDGE IN CENTER OF CUTTING PATH Width of Deck SGB024 SLOPE CUT - SLOPING RIDGES ACROSS WIDTH OF CUTTING PATH Width of Deck SGB025...
-
Page 25: Adjustments
Section 6 PARKING BRAKE ADJUSTMENT WARNING Do not operate the mower if the parking brake is not operable. Possible severe injury could result. The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and the parking brake will not prevent the mower from moving. -
Page 26: Travel Adjustments
TRAvEL ADJUSTMENTS Neutral or tracking adjustments will need to be made if: A. The steering control levers are in the neutral position and the machine creeps forward or backward. (See Neutral Adjustment). B. The steering control levers are in the full forward position and the mower pulls to one side or the other when traveling in a forward direction. -
Page 27: Throttle Control And Choke Adjustments
Authorized Scag Power Equipment Dealer. THROTTLE CONTROL AND CHOKE ADJUSTMENTS These adjustments must be performed by your Authorized Scag Power Equipment Dealer to ensure proper and efficient running of the engine. Should either need adjustment, contact your authorized Scag service center. BELT ADJUSTMENT... -
Page 28: Cutter Deck Adjustments
CUTTER DECK ADJUSTMENTS Cutter deck level, pitch and height are set at the factory. However, if these adjustments should ever need to be made, the following procedures will aid in obtaining the proper cutter deck adjustment. - Note - Before proceeding with the cutter deck adjustments, be sure that all tires are properly inflated. - Page 29 Section 6 ADJUST HERE 2007 SFZ RSDA Figure 6-6. Cutter Deck Pitch Adjustment - Note - To prevent the cutter deck from teetering, all four (4) cutter deck hanging chains must have tension on them. If all four chains do not have tension on them and the deck teeters, you must readjust the cutter deck as outlined in the procedures above.
-
Page 30: Electric Clutch Adjustment
ELECTRIC CLUTCH ADJUSTMENT The electric clutch serves two functions in the operation of the mower. In addition to starting and stopping the power flow to the cutter blades, the clutch also acts as a brake to assist in stopping blade rotation when the PTO is switched off or the operator presence circuit is interrupted. -
Page 31: Maintenance
Section 7 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS HOURS BREAK-IN 100 200 400 (FIRST 10) * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions MAINTENANCE PROCEDURE Check all hardware for tightness Check hydraulic oil level C h e c k a l l b e l t s f o r p r o p e r alignment Check hydraulic hoses for leaks Check engine oil level... -
Page 32: Hydraulic System
HYDRAULIC SYSTEM A. CHECKING HYDRAULIC OIL LEvEL The hydraulic oil level should be checked after the first 10 hours of operation. Thereafter, check the oil after every 200 hours of machine operation or monthly, whichever occurs first. - IMPoRtANt - If the oil level is consistently low, check for leaks and correct immediately. -
Page 33: Checking Engine Crankcase Oil Level
Section 7 Remove the top port plug from both axles before filling with oil. See Figure 7-4. REMOVE TOP PORT PLUG Figure 7-4. top Port Plug Location Fill the hydraulic expansion reservoir with 20w50 motor oil until the oil just appears at the bottom of each axle top port. -
Page 34: Engine Fuel System
C. CHANGING ENGINE OIL FILTER After the first 20 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter after every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator’s Manual for instructions. ENGINE OIL FILL &... -
Page 35: Engine Air Cleaner
Section 7 If fuel is spilled on clothing, change clothing immediately and wash affected skin. Replace gas cap and tighten securely. B. REPLACING IN-LINE FUEL FILTER ELEMENTS The engine fuel filter should be replaced after every 400 hours of operation or annually, whichever occurs first. See Figure 7-7. -
Page 36: Drive Belts
WARNING Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEvERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below. -
Page 37: Cutter Blades
Section 7 CUTTER BLADES A. BLADE INSPECTION Remove the ignition key before servicing the blades. Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling. WARNING Always wear proper hand and eye protection when working with cutter blades. -
Page 38: Tires
CUTTER BLADE LOCKWASHER 5/8-11 x 1-1/2" HEX HEAD BOLT TORQUE TO 75 FT/LBS Figure 7-9. Blade Replacement - Note - Be sure that the blade is installed with the lift wing toward the top. Install the cutter blade onto the cutter spindle shaft. Secure the blades from rotating and torque to 75 ft/ lbs. -
Page 39: Illustrated Parts List
Section 8 ILLUSTRATED PARTS LIST SCAG APPROvED ATTACHMENTS AND ACCESSORIES. Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. Scag approved attachments and accessories: • GC-SFZ (p/n 9074, requires p/n 9069, 9070 9071 or 9073 baffle kit) •... -
Page 40: 36 Cutter Deck
36 CUTTER DECK Section 8 2008 SFZ 36CD... - Page 41 Section 8 Ref. Part No. Description 04021-09 Nut, Elastic Stop 3/8-16 424615 Bracket, Belt Guide 04043-04 Flatwasher, 3/8-.391 x .938 x .105 424367 Dust Shield 04112-06 Nut, 3/4-16 Spiral Lock 04063-01 Key, 1/4 x 1/4 x 1-1/4" 483667 Belt, Cutter Deck 483442 Pulley, 5"...
-
Page 42: 48, 52 & 61 Cutter Decks
48, 52 & 61 CUTTER DECKS Section 8 2007 SFZ CD... - Page 43 Section 8 Part No. Description 424528 Belt Cover 425260 Belt Cover 04063-01 Key, 1/4 x 1/4 x 1-1/4" 04112-06 Nut, 3/4-16 Spiral Lock 483323 Pulley, 5.13" OD - 25mm Bore 483324 Pulley, 5.73" OD - 25mm Bore 484026 Pulley, 6.32" OD - 25mm Bore 04021-09 Nut, Elastic Stop 3/8-16 04043-04...
-
Page 44: Cutter Deck Controls - Sfz36
CUTTER DECK CONTROLS - SFz36 18 23 Section 8 2008 SFZ 36CDC Rev 1... - Page 45 Section 8 CUTTER DECK CONTROLS - SFz36 Ref. No. Part No. Description 483341 Cable, Deck Lift 04003-31 Bolt, Carriage 3/8-16 x 3/4" 424827 Support, Idler Arm 43710 Spacer, Deck Lift Pivot 04001-90 Bolt, Hex Head 1/2-13 x 3-3/4" 04001-183 Bolt, Hex Head 1/2-13 x 1-3/4" 483453-03 Bearing 04040-07...
-
Page 46: Cutter Deck Controls - Sfz48 & Sfz52
CUTTER DECK CONTROLS - SFz48 & SFz52 14 26 18 23 Section 8 2008 SFZ48&52 CDC... - Page 47 Section 8 CUTTER DECK CONTROLS - SFz48 & SFz52 Ref. No. Part No. Description 483341 Cable, Deck Lift 04003-31 Bolt, Carriage 3/8-16 x 3/4" 424476 Support, Idler Arm 43710 Spacer, Deck Lift Pivot 04001-90 Bolt, Hex Head 1/2-13 x 3-3/4" 04001-183 Bolt, Hex Head 1/2-13 x 1-3/4"...
-
Page 48: Cutter Deck Controls - Sfz61
CUTTER DECK CONTROLS - SFz61 14 26 18 23 Section 8 2009 SFZ61 CDC... - Page 49 Section 8 CUTTER DECK CONTROLS - SFz61 Ref. No. Part No. Description 483341 Cable, Deck Lift 04003-31 Bolt, Carriage 3/8-16 x 3/4" 424476 Support, Idler Arm 43710 Spacer, Deck Lift Pivot 04001-90 Bolt, Hex Head 1/2-13 x 3-3/4" 04001-183 Bolt, Hex Head 1/2-13 x 1-3/4" 483453-03 Bearing 04040-07...
-
Page 50: Sheet Metal Components
SHEET METAL COMPONENTS TO RH REAR SEAT MOUNTING BOLT TO RH FAN COVER Section 8 2008 SFZ SMC... - Page 51 Section 8 Part No. Description 483408 Seat Assembly 483544 Back Cushion 483545 Bottom Cushion 483549 Arm Rest Kit 483543 Seat Adjustment Kit 483412 Seat Belt Assembly, Retractable 461990 Hardware Package, Mounting 462034 Seat Base w/Decal 483371 Spring, Seat Latch 451883 Seat Latch 04021-09 Nut, Elastic Stop 3/8-16...
-
Page 52: Sfz Roll-Over Protection System
Section 8 SFz ROLL-OvER PROTECTION SYSTEM... - Page 53 Section 8 SFz ROLL-OvER PROTECTION SYSTEM Ref. No. Part No. Description 04001-184 Bolt, Hex Head 1/213 x 3-1/4" Gr. 8 04040-13 Flatwasher, 1/2 - .562 x 1.375 x .109 43743 Bushing, SFZ ROPS 04021-19 Nut, Center Lock 1/2-13 462106 ROPS, SFZ36 462021 ROPS, SFZ48, SFZ52 &...
-
Page 54: Drive System Components - Sfz36
DRIvE SYSTEM COMPONENTS - SFz36 14 34 45 46 TO RIGHT DRIVE PUMP Section 8 36 34 2008 SFZ36 DSC... - Page 55 Section 8 DRIvE SYSTEM COMPONENTS - SFz36 Ref. Part No. Description 483707 Engine, Briggs & Stratton 20hp 483706 Engine, Kawasaki 17hp 04061-01 Cotter Pin, 3/32 x 1" 04069-01 Pin, Rue Cotter 3/8" Dia. 04062-02 Hair Pin, .080 x 1.19" 04019-03 Nut, Serrated Flange 5/16-18 44162 Rod, Brake Adjustment...
-
Page 56: Drive System Components - Sfz48, Sfz52 & Sfz61
DRIvE SYSTEM COMPONENTS - SFz48, SFz52 & SFz61 14 34 45 46 TO RIGHT DRIVE PUMP Section 8 36 34 2008 SFZ DSC Rev.3... - Page 57 Section 8 DRIvE SYSTEM COMPONENTS - SFz48, SFz52 & SFz61 Ref. Part No. Description 483465 Engine, Briggs & Stratton 26hp 483516 Engine, Kawasaki 19hp 484133 Engine, Briggs & Stratton 28hp (61 Only) 04061-01 Cotter Pin, 3/32 x 1" 04069-01 Pin, Rue Cotter 3/8" Dia. 04062-02 Hair Pin, .080 x 1.19"...
-
Page 58: Fuel And Electrical System - Sfz36
FUEL AND ELECTRICAL SYSTEM - SFz36 SEAT SWITCH SOLENOID CLUTCH Section 8 ENGINE MOUNT BOLT 2008 SFZ36 FES... - Page 59 Section 8 FUEL AND ELECTRICAL SYSTEM - SFz36 Ref. Part No. Description 48298 Fuse, 20 amp 483473 Switch 483621 Wire Harness, Main 483474 Switch, Seat 483537 Hourmeter 48029-13 Battery Cable, Red 25" 48029-11 Battery Cable, Black 27" 04001-44 Bolt, Hex Head 1/4-20 x 1/2" 04020-02 Nut, 1/4-20 483557...
-
Page 60: Fuel And Electrical System - Sfz48, Sfz52 & Sfz61
FUEL AND ELECTRICAL SYSTEM - SFz48, SFz52 & SFz61 SEAT SWITCH CLUTCH ENGINE MOUNT BOLT Section 8 THROTTLE CHOKE 2008 SFZ ES... - Page 61 Section 8 FUEL AND ELECTRICAL SYSTEM - SFz48, SFz52 & SFz61 Ref. Part No. Description 48298 Fuse, 20 amp 483473 Switch 483621 Wire Harness, Main 483474 Switch, Seat 483537 Hourmeter 48029-13 Battery Cable, Red 25" 48029-11 Battery Cable, Black 27" 04001-44 Bolt, Hex Head 1/4-20 x 1/2"...
-
Page 62: Zt-3100 Hydraulic Axle Assembly
zT-3100 HYDRAULIC AXLE ASSEMBLY 17 18 Section 8 32 33... - Page 63 Section 8 zT-3100 HYDRAULIC AXLE ASSEMBLY Ref. Part No. Description HG71512 Kit, Fan & Pulley (SFZ36) HG70489 Kit, Fan & Pulley HG51244 Nut, Hex Locking 1/2-20 HG51523 Washer, Slotted HG52576 Fan, 7" Dai. (10 Blade) - (SFZ36) HG51862 Fan, 7" Dai. (10 Blade) HG50302 Pulley, Cupped 4-1/2"...
-
Page 64: Zt-3400 Hydraulic Axle Assembly -Sfz61
zT-3400 HYDRAULIC AXLE ASSEMBLY -SFz61 51 52 65 66 Section 8 ZT-3400 Exploded View... - Page 65 Section 8 zT-3400 HYDRAULIC AXLE ASSEMBLY - SFz61 Ref. Part No. Description HG72034 Kit, Fan & Pulley HG44133 Nut, Elastic Stop 1/2-20 HG51523 Washer, OD Slotted .53 x 1.63 x .06 HG51862 Fan, 7" (10 Blade) HG53619 Pulley, 4-1/2" HG53029 Ring, Retaining HG51161 Seal, Lip 17 x 40 x 7...
-
Page 66: Replacement Decals And Information Plates
REPLACEMENT DECALS AND INFORMATION PLATES COMMERCIAL GRADE MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS: 4,487,006 4,991,382 5,133,176 6,192,666 7,065,946 Section 8 MOWER DECK 4,885,903 4,920,733 4,967,543 4,998,948 5,042,239 5,117,617 5,826,416 5,832,708 5,865,018 6,766,633 6,892,519 6,996,962 PATENTS PENDING... - Page 67 Section 8 REPLACEMENT DECALS AND INFORMATION PLATES Ref. Part No. Description 483402 Decal, Belt Cover 483405 Decal, Warning 483425 Decal, ROPS 483505 Decal, Spinning Blades 481568 Decal, Traction Control 483633 Decal, Seat Replacement 483710 Decal, 36 Commercial 483494 Decal, 48 Commercial 483495 Decal, 52 Commercial 484044...
-
Page 68: Electrical Schematic
ELECTRICAL SCHEMATIC INTERLOCK SWITCH OPTIONAL BLACK LIGHT ACCESSORY BLACK HOURMETER BLACK RED W/YEL STRIPE GREEN L.H. NEUTRAL BLACK W/RED STRIPE SWITCH WHITE WHITE GREEN BLACK BLACK SWITCH RED W/YEL STRIPE RED W/YEL STRIPE WHITE WHITE GREEN BLUE GREEN WHITE WHITE SWITCH GREEN RED W/YEL STRIPE... -
Page 69: Limited Warranty - Sfz
500 hours (whichever comes first) (First and second year of the warranty covers parts and labor. The third year covers parts or labor to repair) for non-commercial use. The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve the right to request components for evaluation.